Models > 11016852501 > Instructions

11016852501 Kenmore Washer - Instructions

All installation instructions for 11016852501 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016852501
76-90 of 1037
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No cold water entering machine

  • Customer: Steve from Bethel ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 5 of 6 people found this instruction helpful
After uplugging and removing the hoses from the back of the washer, 1 - Removed four screws that secure control panel to top of machine and tilted panel toward front. Disconnected wiring plugs as req'd to gain more access. 2 - Removed the two gold colored clips that secure the top to the lower sheetmetal housing and tilted the lower housing away from the back of the machine. 3 - Removed the shield that is clipped to the back just above the inlet valve assy. 4 - Removed the hose clamp from the valve, disconnected the four wires to the valve (note their position), Removed the single screw that secures the valve assy to the back and removed the valve assy. Installation is reverse of above.

Water Pump was leaking

  • Customer: Rick from Liberty SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

Washer would'nt spin

  • Customer: Dean from Poplar Grove IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

Washer basket off-center and wobbling during spin cycle

  • Customer: Craig from Woodland Hills UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

tub oscillation

  • Customer: leonard from phil campbell AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 6 of 10 people found this instruction helpful
placed washer on side and installed new pads
and returned washer upright

Washer would not work in agitate or spin cycle

  • Customer: yesenia from apopka FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off without unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.

The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.

It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.

washing machine will agitate but not spin

  • Customer: Robert from Manchester CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 10 of 22 people found this instruction helpful
I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.

No spin or agitation

  • Customer: Charles from Terre Haute IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
I removed four srews holding the control panel and laid it to the side, then removed a screw holding the ground on and disconnected the electrical connection. The lid needs to be open to remove the switch. Just remove the switch and reverse sequence. To replace the coupling , I laid over the washer and removed two screws holding the straps connecting the motor to the transmission. After seperating, I pulled off old couplings and reinstalled the new ones on both the motor and transmission. I had to tap couplings on. Then reversed the installation and set backup and tried it out. It worked great.

the washing machine would pump the water out, but the agitator would not spin, and it was making noise.

  • Customer: mario from eastchester NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the motor was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts.
Thank You,
Mario for Eastchester, NY.

drum SLAMMING into the back of the washer when sipnning

  • Customer: WILLIAM from DAYTON KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago

drain hose for washer was cracked and leaking

  • Customer: richard from orange CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
This was really easy and the part came in like 2 days. All I needed to do was flipthe washer on its side and remove the old hose...a couple screws and install the new one...it was a perfect match so ...no issue.

Coupling on Whirlpool Washer gave out

  • Customer: Ronny from Santa Monica CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 3 of 3 people found this instruction helpful
The coupling, made of plastic and rubber, on our Whirlpool washer gave out. Done the same repair nine years ago and knew what to do. Here is a short summery:

1. unscrew the 2 screws that hold the control panel on top of the machine in place

2. unscrew the screws that connect the housing with the back panel

3. pop the 2 clips under the control panel to release the back panel

4. with the back panel loose disconnect everything
that is pushed, screwed or clamped on and take the back panel off (don't worry about remembering where things go, everything can go only one way together again)

5. slightly lift the housing of the washer in the back to remove, that gives you access to the coupling in front of the machine

6. I personally like to put the washer on its back and do the repair that way. However, if you want to
leave it standing that is gets you there too.

7. take the screws out of the brackets that hold the pump (the thing with the two hoses attached to it)
in place and snap off the brackets; lift up the pump and put aside

8. you can now remove the broken coupling

9. check for any fragments and clean off what needs to be cleaned

10. replace the coupling

11. reverse the order of steps 1 to 7; make sure that the all electrical connections and hoses are connected!

12. test

washing machine motor would run but the part that run the transmission was broke

  • Customer: LYDIA from HIGH SHOALS NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 3 of 3 people found this instruction helpful
We had to take the motor out and remove the coupling, when putting it back together we had some problems because the washer was on its side and the lid was open. After putting the motor and coupling back together we tried to turn it on, unknowing to us the lid was open so nothing would happen, finally we realized the lid was open. The actual repair was not complicated, just human error made it seem than way

My washer stopped mid-cycle and acted completely dead

  • Customer: Jeff from Ventura CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
I thought the click of the lid switch sounded different so I pulled the top console and tested it for continuity in both positions and found none. When I by-passed the switch the washer started up, so I knew what the problem was. There are four screws involved to remove the console which reveals the lid switch to the left side. There's a single screw for a ground wire but the switch itself is simply snapped in place after disconnecting the wire harness plug (must be done with the lid open btw).

I was lucky to diagnose the problem accurately so that the first thing I suspected turned out to be the problem!

Motor runs, but tub does not spin or agitate

  • Customer: Danny from Woodstock GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 3 people found this instruction helpful
Woulkd have taken alot less time had I not taken off the control board, back...etc. Laying the unit on its back is perfect. Took it out into the garage when I could have done it in the laundry rooom with very little water loss.
1. Removed all hoses connected to top of motor. This was not very easy since the spring clamps had been in the same place for 20+ years. Also removed all wire harness connected to and from the motor.
2. Removed metal clamps from top of motor unit, and removed the plastic "valve".
3. Removed screws holding in clamps on each side of the motor used to hold motor on motor plate. Removed motor. Trick is to make sure that the back clamp stays in place...makes it a little easier when you go to re install.
4. Cleaned out around agitator shaft, and fitted one side of the coupling and the neoprene type joiner on to the agitator shaft.
5. Fitted other side of coupling on to motor...This is where it got a little tough......and then placed motor unit on the motor plate, making sure to line up teeth to neoprene joiner.
6. Replaced clamps on each side of the motor and screwed in nuts holding them in place.
7. Replaced plastic "valve" and the clamps that hold it in placed...back one is a little tough.
8. Reattached hoses to "valve" and hooked all wire harness back into place.
9.Tested perfect...little burning smell on first spin....but works great now!!
All Instructions for the 11016852501
76-90 of 1037