10652203100 Kenmore Refrigerator - Instructions

Replaced control and motor on the basis that most respondents found this unit to be at fault when the icemaker failed. Unfortunately, this wasn't the problem. Sudsequently, I replaced the electrionic boards which did fix the system. It would have been helpful (and less expensive) if the patrsselect website provided more help with problem diagnosis. Otherwise, the website is great!

Remove ice unit to take out ice. Remove both boards and replace.Had to unplug refig to thaw out water line because it froze when unit would not make ice.

It was a very simple repair. The only frustration is that all I needed was a small plastic part on the motor assembly but had to buy the entire assembly. Glad that I found the assembly much cheaper on your site, but wish I could have just bought the small plastic part.

took out the old one and replaced with new. PERFECT FIT.

Removed outer cover. Removed control bracket which holds the water/ice dispenser paddles. Removed paddles from old/broken bracket, plastic pins were broken where the paddles hinge. Placed on new bracket placed screws and it was done. Very simple repair. Part cost less then $18.00 including shipping. Saved me mucho dollars!!!!

hardest part getting the putty knife in right place to pop off cover---found the plastic bracket was broken where the switch was held in place---- so ordered new switches and bracket ---- got the parts in 3 days--good service--easy job 2 do and saved lots of $$$$$$$$---

After determining the control boards weren't working (by the light was not working) I replaced the control boards. By the way I received the parts in only a day and a half.It only took about 15 mins. The parts came with a troubleshooting guide witch was a little difficult to understand, but I got through it. The new parts were working but still not making ice. The water line had frozen. My wife and I took a meat injector as a syringe and injected hot water in the line and a air compressor I have and blew air into it also. It works again. As a tip try to blow air into the water line with your mouth to see if its clear.

With service sheet, Enter service dagnostic mode, NO-6 is Desrost heater / Bi-metal Component status indicator shows 02 , it means Bi-metal is open, It should read 01,It's cover with Ice ( bellow 32 Dig. F )Mostly it open at 50 dig. F, To replace remove lamp cover and lamp + six hex screw with 1/4" nut driver, pull back cover ( with commen requirement to turn of power and deice the evaporator coil )out, bi-metal element is top at enterance of coil,cut both wire near bi-metal, join new bi-metal with wire nut or Insulated wire Jointer, Tape jonts proper,do neat work no hanging wire, Replace back removed parts back,Turn power back

Removal of the old heating element was really easy. The video on Partselect.com was majorly helpful in reassuring my confidence in doing this repair.

I watched your video and did just as he did. The video made it real easy and rather simple. It looked like it was going to be a mess until I watched the video.

Unplugged the refrigerator removed the cover and 3 screws. Pulled the old part off and replaced with the new and screwed it back on. Replaced the cover plugged it back in and it started working again.

I watched the short video at this website about replacing the bracket first. Then I replaced mine. Everything went smooth. No problems. Try it yourself.

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

Took cardboard back panel off and looked at compressor number and found right part number from the compressor start kit. It was somewhat confusing as you have to take that part of existing unit. The run capacitor is different size but worked. Worth the trouble figuring out instructions for parts but is working great right now.

Greatest thing about this company was properly describing in an easy clear manner along with the video. A picture is worth a thousand words. A video is worth? Disconnecting wires in back of freezer was a little hard. I didn't know you would have to wait for a complete cycle before the water would fill and make the first batch of ice. I thought it was not hooked up properly and took it back apart. This time I left it, waited and in a few hours, it started making the first batch of ice. Great company, price and fast shipping. Would definitely buy from again