10650444900 Kenmore Refrigerator - Instructions

Your repair video was spot on. Should have watched it before I removed the old defective part. Would recommend it for anyone with same problem. I'll call on you again. Thank you. Billy

Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.

This is for the refrigerator, not the freezer door which is more complicated. First empty the refrigerator door of food and removed the shelves. Remove the hinge cover on the top hinge by removing one bolt. Then, holding the door, remove the top hinge by removing the three bolts in the bracket (not the bolt in the recessed hole). Lift the door off the lower hinge and lay the door on its edge on the floor. Pry the old Door Cam out of the hole in the door with a knife (my Door Cam was ground completely flat). Insert the new Door Cam. Remove the old Lower Door Cam from the lower hinge and insert the new Lower Door Cam. Pick up the door and lower the door onto the lower hinge ensuring the lower hinge pin inserts into the hole in the Door Cam on the door. Reinstall the upper hinge and insert bolts without tightening. Align door and then tighten hinge bolts. Reattach top hinge cover and tighten the single bolt. Test the door to ensure it closes and stays closed. I had to remove the door a second time to rotate the Door Cam slightly to ensure cams were better engaged (tongue in groove style) when the door was closed. Reinstall the shelves and load the door with food.

Hi, this was an easy repair job. And, after I was done I felt like McGyver. It took me about 1 hour. The hardest part was getting ice maker's power source disconnected. That was tricky; you have to remove the housing that covers the power connector.

I rearranged the other bins on my refrigerator door. I checked the space between the bins, to make sure I could remove and insert items easily. I put my new bin in place, I made sure it was secure and I put taller items in the new bin.

After our four year old refrigerator door wouldn't stay closed as a do it yourself kinda gal I found this website that assisted me in an easy and inexpensive fix. The "plastic" yes, "plastic" piece on the bottom of the door was worn down to nothing. My only suggestion is to call in your order, the customer service folks will help you order the right cam for your model. The next thing is to change both cams if you have a side by side. We changed the fridge side which fixed the problem, then realized the cam on the freezer needed to be changed to make it level. Great customer service!

my 17 year old son actually repair it ...it took him all about 5 minutes to install the part and put that refrigerator cover back on ...very easy fix and save me a bundle of cash ...thank you very much and I will be doing more business with you

I was ready to spend the $$$ on a repair person when my wife (smart woman) suggested I go on line to see if we can fix it ourselves. I (luckly) found your company and your website made it easy to find the right part plus as an extra bonus you had a video that showed how to switch out both control boards. To top it off, the package came so fast ( the next day - even with standard shipping ) I did not think it was the parts. 10 or so minutes with a Phillips screwdriver and we were back in business. THANK YOU ! ! ! !

Unplug the Unit first! Unscrewed the sensor covers on both sides. Snap off the old, snap on the new. Replace the covers and screws.

Replaced the Ice Maker

Followed the steps in the video on your website, and was amazed at how simple and fast it was done, with no problems.

We were reluctant to replace the icemaker on a 10-year old refrigerator that required a leak to be patched 2 years ago, but since the patch seems to be holding, we went ahead with the icemaker. Was about the same price as buying a portable icemaker and who wants that sitting on the counter?

Removed the broken icemaker. Removed the tray that is attached to the old icemaker and screwed it into the new icemaker. Then, I installed the new icemaker first by plugging in the control wires, then sliding the icemaker into the freezer, then screwing it into freezer. BY next morning, the icemaker made ice!

Ordered part and w/ help of a friend in it went.Devlivery was prompt. Receptionist on phone was great. If every company had one like her everyone would be a happy camper.Would recommend your company to anyone.It was a most pleasant experience.

Neither the OEM instructions nor any of the PartSelect videos explained BOTH ends of the tube for my particular appliance. All very thoroughly covered the obvious connection with the water valve from the wall. However, the push valve end for my KitchenAid is supposed to insert into the water filter chassis, which can barely be seen from the back of the appliance, much less reached with any tool. In order to make the repair, one must either remove the water filter chassis (which I attempted unsuccessfully), or put the appliance up on jacks in order to reach the push valve site.