10641514100 Kenmore Refrigerator - Instructions

Removed the door, laid the door on its side, and pulled the worn part from the door. Inserted the new part, reattached the door, and it works like a charm. The parts diagram online was very helpful. I ended up purchasing a part I didn't need in case an unidentified washer came with it, but I didn't need it. No big deal.

We thought we were in need of a new seal around the door but as my husband checked the door he found out it was a piece under the door that holds it up so the door was not sealing right when it closed. I went on line. Found this site and found my fridge. My husband viewed the pics of the parts and figured out we needed a cam. I ordered my part and could not believe it came the very next day!!! I didn't even pay for anything other then regular delivery. He took off the door and it was simple to just slip on the new part and replace and put the door back on.. Nothing much to tell here. Less then 30 minutes. Thank you so much for the quick service getting it out to us. I was about to put a child lock on the door just to keep it closed..

I removed the items from inside the door and removed the door from the refrigerator at the upper hinge. Removed cam from the door and replaced with the new one. Checked for proper operation and it's quiet as a mouse. I love it.

work like new

Took out the old broken part and installed the new part. Perfect.

take off the face plate of fridge and follow the cable back to the compartment where fridge and freezer meet. once out, had to remove transluscent cover from thermostat wire - easy and feed that same cover onto the new thermostat. Slow is better and using pliers to force 1/4 to 1/2 inch at a time into the tubing - easier if you have 2 people. After that just put the length back in and insert the controller back in the panel and plug in the electricity again. (to the thermostat). 30 minutes later - cold fridge.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Looked up on you tube to verify and see "secrets" to installation.

Removed the door and replaced the lower door cam. Old lower door cam was completly stripped. Insatalled new one and door sealed again! Yay!

removed old unit and installed new one. very straight forward process. fridge has performed flawlessly since. Thanks

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

This install was simple and fast. I ordered the drawers from PartSelect.com and received them in less than a week! Switching them over and putting them in was quick and easy. THANKS to a great experience I plan on ordering from PartsSelect whenever I have any future appliance troubles!

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.

I took out all the condiments from the shelves, gasped at how dirty the shelves were, took out the shelves and clicked the brand new, clean shelves into my refrigerator. I threw away expired condiments and replaced the still great ones. I closed the fridge and gave a sigh of relief of yet another task checked off my list.