10641512101 Kenmore Refrigerator - Instructions

Watched your installation how to video. Applied same procedure. Went smoothly.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

The hard part of the repair was getting the wife to empty the refrigerator door shelves. Once that was done simply removed the three screws on the door on the top of the door removed the bottom cam located on the bottom inside of the door. One of the simplest repairs I've ever done. Watching the you-tube video was a great help.

simply replace the compressor start and delay

Replaced original ice-maker with the ice-maker from the kit. Operational check was good.

Was very simple once I found out where the defrost timer was located. I had a friend walking me through trying to find the location on the phone. Not all models have them in the same place. Once the part was located all I had to do was remove the cover, unplug the old one and plug the new one in just the way the old one came off. The black wire was easy to locate on the old and just matched it up. Put the cover back on and plugged it in. It was no time till I started feeling it cool. Checked both top and bottom with thermomater and it was where it should be within 12 hours. I am happy and using it again. Was almost ready to throw it out. Did not know it was so cheap to fix one. Nothing anyone can't handle. If this woman can do it anyone can.

Took old drawer out, put new drawer in. When I first opened the new drawer I was a little disappointed as the printing on the edge of the crisper (where it says humidity low-high) was a different color than my existing drawer, I know it's such a small detail that nobody would notice but me. My fridge is almost brand new and I'm the one who broke the drawer so I was a little sad but then realized that I could remove the edge of the drawer and replace it with my old one... VIOLA brand new drawer with purple letters! The drawer itself came so fast, I believe it was 1-2 days to my door! Thank you Part Select

Followed the video, very helpful! Basically a walk in the park.

took out old drawer, slid in new drawer and transfered food

Replaced old drawer with new. Did have to remove white handle, the new one doesn't come with one. It was simply a matter of prying up the edge until it would come off and snapping it in place on the new one. Used the screw driver to lift pry up the edge.

Unplugged Refer...Cleared top shelf...removed screws/covers to expose thermostate and capilary tube...removed old thermostate takeing care to notice how Capilary tube was routed and electrical connection were made (wire color coding)...removed sheath on old capilary tube and installed on new, always making sure to not "kink" tubing...installed new part just as the old one was...plugged refer back in and enjoyed trouble free operation.

My fridge is a little different from the video model. The Controls in the fridge are located on an "arm" which swings down when the two screws are removed from the sides. It was not necessary to remove a front plate or knobs. However, I found when I got in to it that the old timer was not held by screws, but by plstic posts which had these "speed nuts" on them. This is a little metal plate which fits over the plastic post and bends to lock it in place. When you try to remove it, it acts like a barb, holding the little sucker on. I ended up bending the ends of those little suckers up tight against the post and twisting and pulling with needle-nose pliers. I broke one post like others before me commented, but one stayed intact. The only break at the top, so there ie still post left to hold the new timer. Once it was off, I was able to replace easily. The directions for choosing the right prong were a little confusing, but follow your gut and go with the wire colors. My schematic found in the bottom of the fridge did not look like any of the drawings, but I could match the wire colors. I also asked "Just Ask" for help, to make sure. My gut instinct was right. My fridge is now working again beautifully. If a housewife with no appliance repair knowledge can do it, so can you. I fixed my dryer with PartSelect too!I will never call another repair man until I have checked this site to see if I can do it myself. Bet I have saved $600 so far at least!

The repair was super easy and the part worked like a charm. I love my new ice maker! I had to take out the top freezer shelf just so I could fit my head in the freezer to find one screw, but otherwise all went fine. Ice maker is held on with two top screws and one bottom screw. Loosen the two top screws, remove the bottom screw and lift out the ice maker. It plugs into wires on the inside, back of the freezer so this has to be unplugged. Plug in the wires for the new one, slide it down onto the two top, loose screws, tighten those and screw in the bottom one, replace freezer shelves and you are ready for ice...with no huge iceberg fouling up the ice in your ice cube tray. Simple! The wiring thing worried me when others described it, but it's no harder than plugging in a lamp, really. If I can do it, anybody who can stand on a shorty ladder can do it.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.