| |
12 of 20 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerEdward from Brooklyn NY
The main tray holding the vegetable bins had broken and prevented the bins from operating smoothly
Removed all food and slid the broken shelf tray. I replaced the right side tray support and installed the new tray.
I also had to replace the front of one of the bins, as the shelf was binding the bin and the front handle had broken due to amount of force needed to open that bin.
Once the tray was in properly, the bins worked normally.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Crisper Drawer Cover Support
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
Customermichael from hanford CA
My shelf supports broke
I pulled out the old pieces and poped what I couldn't into the foam insulation behind the support. Then I placed the new piece in the hole and popped the plastic pin to seat the support. bang. the only problem I had was knowing if it was the right part by the picture. The little pin that had to be pushed through kinda threw me.
|
2 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDiptendra from Palo Alto CA
The cover storage pan broke, so I needed to replace it.
I removed the drawer, removed the cover and replaced with the new one. One of the cover support has a small crack and thus i ordered two with the intention of removing them. As they still can support the weight of the drawer I did not remove them.
I looked at other companies for this part throgh the internet but your drawing is very clear and it was real easy to select the part. The person with whom I talked was very helpful .
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerDavid from Cumming GA
Drawers and support brackets broken
removed good old clear plastic drawer fronts by prying loose with a screwdriver at the bottom of drawer.and sliding out upwards. placed old fronts on new drawers by sliding downward and snaping in place. removed old support guide using a nut driver and installed new one.removed both crisper drawer cover supports prying out with a screwdriver.pushed broken post of these supports back into the refrigirator wall with a flat punch.installed new supports and pushed locking post in with my punch and hammer. installed new cover storage pan.put in new drawers top and bottom with glass.about a 20-30 minute job.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Crisper Drawer Cover Support
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerArand from Yorktown IN
The original support was broken, tried epoxy and it only held for a few months before breaking again
All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerHarold from Weatherly PA
Broken part
removed broken support and replaced it .
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers
CustomerRaymond from Anchorage AK
Freezer drawer rail caps and crisper drawer supports were broken
I removed the old parts, installed the new parts and reassembled the crisper drawer and rails. For less than $50 delivered I was able to bring the unit back to service for our family.
|
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customerbeth from brooklyn NY
Broken plastic pieces
Removed the old support bar which was broken, stuck the new one in, and adjusted the height. Fit perfectly.
The crisper draw cover supports were stuck in the frame. I used a screw driver to pry them loose. The new ones fit in perfectly, and voila - a perfect fit.
Refrigerator door shelf bin snapped into place with no problem.
Very satisfied with the time to receive parts, time to do repair, and final outcome. Would definitely order from you again.
|
0 of 2 people found this instruction helpful
Parts Used
-
- Crisper Drawer Cover Support
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerWAYNE from NOVATO CA
The supports for the crisper cover had broken and the draws would not open correctly
I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.
|