http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/35998.gif
See part 16 in the diagram

Hinge Pin

PartSelect Number PS2344472

Sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not dispense detergent or Jet Dry.
  • Door latch failed.
  • Compare At

    $4.61
  • You Save

    $.77
  • Your Price

    $3.84
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Short Hinge Pin

Part Number 2202583

$2.92
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 15 reviews What's this?
1-15 of 15
 

54 of 75 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers, Socket set

Customerrichard from austin MN

Drains but doesn't spin, door lock does not engage.

Door locked light did not come on and did not have 120 VAC across the Wax Motor. Also the Wax Motor did not extend out to make contact with the Door Lock, Spin Enable Switch. General guidance is to replace drive belt and to replace Wax Motor along with the Door Lock, Spin Enable Switches (total of two limit switches). This did not correct the problem. Checked for power and traced loss of power back to the Control Board where resistor R11 was found to be burnt out. Replaced Resistor with new Carbon Film unit, rating of 3.9 K-ohms, 1/4 W and 5%. As a prcaution, replace the Triac (manufactue part number NTE5657), component identified as Q6, rating of 0.8 Amp, 600 VAC. Semiconductor parts must be obtained from somewhere other than Parts Select (unable to find in the small town I live in, I located on the internet at Mouser.com). Unit works great now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:Less than 15 mins

Tools

CustomerBonnie from South Orange NJ

The soap dispenser door broke off, I lost the pins and the spring.

The repair is fairly simple except that the diagram on the web site has an error - it reverses the positions of the long hinge pin and the short pin. I kept trying to do it as the diagram showed and of course it didn't work. Then I followed my instincts! The only other difficult part was figuring out which way to insert the spring but there are only a few options so trial and error was the simplest way.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerBrandon from Berea OH

Bad pump

I took off the rear panel and removed the hose clamps and electrical terminals, slid pump out of slot in bottom pan of washing machine. It only took minutes, this was part of a major overhaul. I replaced this as a precautionary measure. Great prices and quick service,

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

Customeranne from gaston OR

Fabric softner, and bleach dispenser not working

First off, unplug the machine.
Next remove the existing screws in the plastic dispenser. Then remove the door, there are two screws holding the door on connecting two brackets which need to be lifted to get them to release.
That gives you the access to the remove the front panel, which is done by pulling on the panel itself.
Once that is done you need to remove the two screws that are in the corners upper left, and right that are holding the brackets that hold down the top of the machine. Remove the brackets by gently turning them.
Once done the lid should easily lift up.
The dispenser can then be disconnected by removing the 2 rubber hoses on top and the the larger rubber hose on the bottom along with the electrical connections under the unit. Keep track of which wire goes to which lead.
After removing the dispenser just do everything in reverse.
The machine is like new, and the repair took about 45min and saved me at least $200 dollars.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKathy from Tulsa OK

Top pin on dispenser door was rusted so the door would come off.

First I removed the 4 screws that kept the bezel in place, removed the bezel. Replaced the new bezel, replaced screws, put new top pin in door and put door on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerSarah from Ephraim UT

The repair went really quick. My husband was able to do it in about 5 minutes. Also the service was amazing. We ordered the part and we got it 3 days later. I have no complaints about ordering from this company and am sure that if I need to get new parts in the future this is where I will get them.

There was 4 screws that held the bevel in that still needed to be removed from the old broken one. Once we removed those we were able to place the new bevel and lid in the correct sport, replace the screws and viola, perfect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

Tools

CustomerCoralie from Centennial CO

The pins on the soap dispenser somehow became disengaged and lost in a wash cycle.

It was difficult to use the guide provided online to determine what position to place the spring in. Finally I realized that the spring had to be placed with the tip that sticks out against the wall of the dishwasher to make the spring action work. The long and short pins were not a problem. How to place the spring was the main problem, but I finally figured it out. I did not need any special tools to accomplish this. I just used a kitchen knife to push the short pin into place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDiane from Lindenhurst IL

The door to the soap dish on the door of the dishwasher had come off and the parts were lost during the wash cycle.

It was a hassle. We didn't have sufficient information in the user's guide to figure out how to attach the soap dish door which had come off back onto the door of the dishwasher, so when we bought the parts, a long pin, a short pin, and a spring (hinge pin), we could only guess how to put it together. The first two times we tried, the pins and spring came off in the dishwasher during a washing cycle and disappeared down the drain. We had to call someone out who just ordered the parts again and said it would cost us $146 to fix, which I thought was ridiculous, so when the parts came, I tried again. This time I figured it out by using a screw driver and hammer to knock the short pin into place while holding the door in place. The door appears to work fine now but, I have yet to use the dishwasher to know for sure.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRichard from Watauga TX

Dispenser bezel broken around screws

Removed 2 of 4 the screws that were holding the Dispenser Bezel in place. Removed the broken Dispenser Bezel and the other 2 screws. Cleaned the 4 screws (remove the detergent) cleaned the inside of the Dispenser area. Assembled the Dispenser lid /bezel assy. Secured the lid / bezel assy to washer with the 4 screws. Installed the syphon cup and syphon cap.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerBarbara from Clarkston MI

Need new lid for detergent cup

Be sure to check for all parts you will need for repair.I didn't realize I needed to get the pins, springs for lid separately when I ordered the lid. So had to have two orders-but the installation was easy-husband did it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerRon from Cottonwood Heights UT

The spring and long pin was gone

installed the pin and spring and then installed the lid with the spring in the correct position to keep the lid open under slight spring pressure. The spring is not a compression spring but a torsion spring.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMilton from portland OR

Broken dispenser, rusted out, pins missing

Easy, took out old dispenser, and put in a new clean one. Really easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerAlan from Burien WA

The detergent lid and pins came loose and the small parts were lost

Went on line to find the part numbers, ordered complete replacement. Simply put the stuff together and replaced the whole cup lid.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

Tools

CustomerTodd from Richmond VA

The soap dispenser lid came off.

At first I tried putting the spring into the lid where the shorter extension of the spring fit tightly into the recessed part of the lid. (If you look at the lid where the hole is for the spring and pin, you see that there is what looks like the arm of the letter "Q".) This worked, but the lid would only open with limited force and would hang down when the dishwasher door was closed.
After looking at it again, I positioned the spring so that the shorter extension of the spring ran through the partially open portion of the spring hole. (Looking at the cup laying flat on the ground, you see that the bottom of the pin/spring hole has a slit in it). This allowed the spring to have greater tension and I have had no more problems. The lid opens with force and stays closed when the dishwasher door is closed (vertical).
This may be a little confusing as I do not know the technical terms for any of this stuff, but I just mess with stuff til it works or breaks, whichever comes first! haha

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 25 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerCarolyn from Panama City Beach FL

Door lock wasn't working

There were two parts to the repair - the Dispenser Lid and Bezel was easy - I did it myself.
My wife, who normally would try to do the repair of the door lock herself has been very busy with her condo rental business. It took six weeks to get her to order the parts and then they sat in the box for two weeks before I convinced her to call her appliance repair company she uses for the renatl condos. They did a quality job for only $79.00. When my wife saw what he had to be do to repair the locking mechanism, she was convinced we made the right decision. The Maytag washer is working like new after weeks of manually adjusting the door latch, sometimes a dozen times, before it would lock and do a high speed spin.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 15