Quick Question!

Have you ever purchased from PartSelect.com before?

11739333-1-S-Whirlpool-WP22002119-Wax Motor
11739333-1-S-Whirlpool-WP22002119-Wax Motor 11739333-2-S-Whirlpool-WP22002119-Wax Motor 11739333-3-S-Whirlpool-WP22002119-Wax Motor http://www.partselect.com/Schematics/Maytag/LW12-33.gif

Wax Motor

PartSelect Number PS11739333

This wax motor is just over two inches long. It is used on some older style washing machines.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Pumps but will not spin.
  • Will not drain.
  • Spins slowly.
  • Burning smell.

Compare At

$17.93

You Save

$2.99

Your Price

$14.94
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 1.8 / 5.0, 2 reviews What's this?
1-2 of 2
 

85 of 124 people found this instruction helpful

Parts Used:
Level of Difficulty: Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Screw drivers, Socket set
Customer: richard from austin, MN

Drains but doesn't spin, door lock does not engage.

Door locked light did not come on and did not have 120 VAC across the Wax Motor. Also the Wax Motor did not extend out to make contact with the Door Lock, Spin Enable Switch. General guidance is to replace drive belt and to replace Wax Motor along with the Door Lock, Spin Enable Switches (total of two limit switches). This did not correct the problem. Checked for power and traced loss of power back to the Control Board where resistor R11 was found to be burnt out. Replaced Resistor with new Carbon Film unit, rating of 3.9 K-ohms, 1/4 W and 5%. As a prcaution, replace the Triac (manufactue part number NTE5657), component identified as Q6, rating of 0.8 Amp, 600 VAC. Semiconductor parts must be obtained from somewhere other than Parts Select (unable to find in the small town I live in, I located on the internet at Mouser.com). Unit works great now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

36 of 58 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Screw drivers, Socket set
Customer: William from Jennings, FL

Door problem on maytag stacked washer/dryer

This is a Washer/Dryer stack unit. Had trouble with the power light not going off automatically. Had to press the power on/off switch to get it to turn off and allow the door to open. While this was going on, the washer would rotate every few seconds and would continue this until the off switch was pressed. Tried replacing the door lock enabler switches and the timer. This did not help. Finally smelled an electrical odor and found that the mother board (located in the upper right front part of the dryer) had a burned resistor (R-11) When this happens, it requires replacing the wax motor and the mother board. This corrected the problem. If you do have problems with the door lock, I would suggest replacing the wax motor as soon as possible. If the wax motor isn't replaced it may burn the new mother board. If I had replaced the wax motor initially, I doubt if the mother board resistor would have burned. Works fine now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-2 of 2