2195202-1-S-Whirlpool-Y04100019-Bake Element - 240V
2195202-1-S-Whirlpool-Y04100019-Bake Element - 240V 2195202-2-S-Whirlpool-Y04100019-Bake Element - 240V http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/33171.gif

Bake Element - 240V

PartSelect Number PS2195202

This bake element has screw-in wire terminals. It's located on the bottom of the oven.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Compare At

    $55.45
  • You Save

    $9.24
  • Your Price

    $46.21
In Stock
Order within the next 11 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 39 reviews What's this?
1-5 of 39
 

37 of 41 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerJohn from Corfu, NY

Old element was worn out (burst in line)

First, I cut the power to the stove to be sure no electrical current could be conducted. Next, I removed the two screws that hold the heating element to the back of the stove. Then, I removed the oven racks and slowly slid the heating element out until I could see the wires that attached to it. Because the element has the female end of the wire, I pulled the male ends out of both the left and right side of the element.. This releases the old element and I discarded it. Next, I took the new element, slide the male ends into the new female ends that protruded from both the right and left side of the element. I crimped these slightly with my pliers to make sure that they would stay secure when I pushed the element into place. With the new element securely attached, I slowly slid the element into place, this forces the exposed wires to be retracted out of sight and in the insulated part of the oven. I then took the two screws that I had to removed in the beginning, and used them to fasten this new heating element to the back of the oven. Finally, I turned the power back on and the element worked fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 18 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerLester from Torrance, CA

Seal rap around oven door window was separating from its frame.

The frame and window were supplied as a completed assembly. About 4 other panels had to be removed prior to installing the new window assembly. This was easy to do with a screwdriver removing about 16 screws and then replacing all panels back in place after replacing the new window assembly. No instructions were supplied with the part, but anyone with a little mechanical abillity could do it. You may need a helper to hold panels in place while they were being screwed back in place. Total job took about one hour

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 7 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerM Lynette from Pawling, NY

My oven would broil but not bake.

First, I made sure the circuit breaker was off to the oven. Next, I removed the two screws that hold the element in place , pulled the element out a few inches and eased the wires apart at the metal connectors. I eased in the new wires, put the two screws back in, and voila. In under five minutes, the oven was fixed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 5 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMaria from Orchard Park, NY

Oven baking element totally burned out and started on fire

Being a single Mom for almost 16 years I have learned to do everything. When the Jenn-Air oven baking element started on fire I freaked out. It turns out that PartSelect.com has the part as usual. I have ordered before for the same appliance and even though it is 15 years old you always have what I need. I removed the old one (two screws in back of oven), measured, logged on, ordered, and the next day installed the new baking element. Even I was able to do this and it fit and worked the first time!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 5 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerFred from New Windsor, NY

Bake element broke in two

My spouse calls me Mr. Breakit--and she's right. I was delighted to read others' accounts that this was easy, but I wasn't sure. When the part arrived, we had 1 hour before company arrived. I took two screws out of the plate (tight--I had to apply a lot of torque), slid the old piece out, attached the new piece, put the screws back in. Voila! (Oh, yeh, do remember to turn the juice off.) We were "cooking" in about ten minutes. So easy a caveman could do it. And I did.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 39