2165432-1-M-Whirlpool-R0000014-Brake Pad Kit
Part Location Diagram of R0000014 Whirlpool Brake Pad Kit
See part 4 in the diagram
( Grid squares measure 1x1 inch )
2165432-1-S-Whirlpool-R0000014-Brake Pad Kit 2165432-2-S-Whirlpool-R0000014-Brake Pad Kit 2165432-3-S-Whirlpool-R0000014-Brake Pad Kit Part Location Diagram of R0000014 Whirlpool Brake Pad Kit
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Brake Pad Kit R0000014

Rated by 7 customers 

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

$ 55.81
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS2165432
Manufacturer Part Number R0000014
Manufactured by Whirlpool
Product Description

Brake Pad Kit Specifications

This brake pad kit contains three brake pads and six installation screws. Helps to bring a rotating cycle to a stop.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will not agitate
This part works with the following products:
Washer.
This part works with the following products:
Amana, Maytag, Speed Queen, Kenmore.
Part# R0000014 replaces these:
AP4245881, 786526, 37810, 40054101, 40081002, 40089401, 637P3, 730P3, R0000014, R9900461
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.7 / 5.0, 7 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
tub would not stop spinning--brakes broke from bolts
Unpluged electric, diconnected dicharge hose from wall drain, disconnected water lines from rear of washer and at wall hose connection, removed lower front panel, removed large front panel, disconnected hoses at motor(put towels at hoses to catch water leakage)THEN-took washer to the garage and tuned up side down. Removed front two tub springs, removed (4) motor bolts, removed electrical harness from motor, remove and replaced new brake pads. NOTE:brake pads need to be somewhat driven(pushed hard) into brake pad slots. Also it was easier to install the rear pad by removing the 4" knock-out at the side of the washer. Somehow reinstall the knock-out to keep mice and animals from entering the interior of the washer. THEN- reinstall all items in reverse order. Any one mechaniclly minded can replace the brake pad. My wife and I saved lots by doing the replacement myself. THE END. Good job Gary Final note:besure to intall the drive "v" belt around the 2" pulley wheel.Very important.
Read less
  • GARY from VILLA RIDGE, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set, Wrench (Adjustable)
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not agitate, but would spin.
Remove the lower access door in the front of the machine. Then I tipped the washer back against the wall to access everything. The pads are alittle hard to push in between the washer pulley disc. So I first pushed in an old broken brake pad off to the side, then was able to push in the new pads. The rear pad is the hardest and I had to release some of the front tub springs and remove the pump hose for access. Overall it went pretty smooth. Thanks for your help!Tim
Read less
  • Timothy from Bowling Green, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was not agitating
Ipulled the front panel off and found that the brake pads had broken into pieces, ordered new pads. Two of the pads were accessed from the front of the machine and were relatively easy to replace by removing the two attaching bolts, spreading gap in area that they fit into with a plastic pry tool. I gained access to the third pad by removing the punch-outs on the side of the machine (circular). If I had not had these prepuched pieces available to me I would have simply cut an access hole in the rear of the machine with a jig saw, (who will ever see it).
Read less
  • John from North Kingstown, RI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washing machine made squeaking noise
Brake pad kit does not come with installation instructions even though it says it does. Remove bottom front panel from washer. There are three brake pads. One of mine (the right one) broke into three pieces and was found on the bottom of the washer. This is how I identified what was wrong. Run the washing machine on the handwash extra light cycle (you could use another cycle, I used this one because I believe it is the shortest), there is a point in the cycle where the disk clamping the brake pads separates from the brake pads and allows you to remove and replace the pads. During other parts of the cycle, the disk is clamped onto the brakes and you could not remove or install a brake pad. I removed the two black hose on the bottom right to get to the right brake pad. Have a 2 gallon bucket ready to collect the water if you did run the washer as above. With difficulty, I was also able to reach around the back side of the right brake pad. I used a socket wrench set. I then removed and replaced the left brake pad. I left the rear brake pad in place. I was not able to get to it.
Read less
  • Peter from Littleton, CO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Socket set, Wrench set
11 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 problems caused by bad brake discs
I first unplugged the washer. I removed the 2 screws that hold the front panel and removed the front panel, they are located at the very bottom outer edges of the front panel.
I then removed 4 of the large springs that are attached to the drum, this washer has six but I only removed the front 4. Removed the two hoses going to the water pump and drain hose, removed 4 bolts that attach the motor to its mounting bracket. Unplugged the wiring harnesses going to motor and what looks like a capacitor mounted to the side of the motor.Then I removed the drive belt. ( when the machine would first start to spin it would make a clacking noise which ended up being a chunk out the the drive belt causing the belt tenshioner to slap causing that noise and letting the drum spin during the wash cycle. So far very easy. I then removed the motor and when it is disconnected you can then remove the water pump. Three hex head bolts need to be removed and it pulls right off. I then removed the six bolts that hold the brake pads in place. I applied silicone grease to the new brake pads and installed them. The pad at the back of the drum was very hard to line up with the holes. I used a very small screwdriver to line up the disc brake mounting holes to get the bolts started and it worked fine. I then put it all back together and it works great. I have to add that I have been an auto mechanic for 28 years and not to brag but this is not your average repair job.
Read less
  • daniel from angola, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
18 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
brake pad was broken and spinning around making noise
this machine seems good to work on because almost every thing is done from the front without pulling it away from the wall. Removed front lower cover by removing two screws. There are three brake pads with two bolts each. applied silicone grease to each pad and put it back togather
  • Alan from Shepherd, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The agitator moved in slow motion at regular setting
took off the front cover.
disconected the wiring from moter.
removed the motor.
replaced the brake pads one at a time used a flat screw driver to spred the plates apart.

The Plasatic Helix Drive Lup
took bolt at the botom of shaft off
this released the Helix drive lug.
took old lug off and inatalled new
replaced bolt and washer.
Read less
Other Parts Used:
Brake Pad Kit Plastic Helix Drive Lug
  • Alvin W. from Reidsville, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Wrench set
13 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dale
March 18, 2018
The belt melted and broke. I put a new belt on. Everything was working fine until it went into rinse and spin mode, when I started to smell something burning (the belt), and when I stopped the machine in spin cycle there was a grinding noise and the tub stopped real fast. It never did this before. I do not know if it is the brakes or the transmission, can you help?
For model number ALW880QAW
PartSelect logo
Hello Dale, Thanks for your question. This could be due to an issue with the idler pulley as well, part number PS11742250. Aside from that, the transmission may be worth examining for signs of wear and tear. I hope this helps.

Was this helpful?
Thank you for voting!
Related Parts:
Idler Pulley Wheel
$63.73

  In Stock
  • 1
Back to Top
You May Also Need ?
Spin Belt
$84.20
$84.20
  In Stock
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2165432
Manufacturer Part Number: R0000014
Brand
Model Number
Description
Kenmore
101939600
Washer - Kenmore Washing Machine Model 101.939600 (101939600, 101 939600) Parts
Kenmore
1019666500
Washer - Kenmore Washing Machine Model 101.9666500 (1019666500, 101 9666500) Parts
Kenmore
1019666501
Washer - Kenmore Washing Machine Model 101.9666501 (1019666501, 101 9666501) Parts
Kenmore
1019666540
Washer - Kenmore Washing Machine Model 101.9666540 (1019666540, 101 9666540) Parts
Kenmore
1019666541
Washer - Kenmore Washing Machine Model 101.9666541 (1019666541, 101 9666541) Parts
Amana
ALW110RAW
Washer - Top Loading
Amana
ALW110RAW-PALW110RAW
Washer - Amana Washing Machine Model ALW110RAW-PALW110RAW (ALW110RAWPALW110RAW, ALW110RAW PALW110RAW) Parts
Amana
ALW210RAW
Washer - Residential
Amana
ALW210RAW-PALW210RAW
Washer - Amana Washing Machine Model ALW210RAW-PALW210RAW (ALW210RAWPALW210RAW, ALW210RAW PALW210RAW) Parts
Amana
ALW210RMC
Washer - Residential
Amana
ALW210RMC-PALW210RMC
Washer - AUTOMATIC WASHERS
Amana
ALW210RMW
Washer
Amana
ALW210RMW-PALW210RMW
Washer - AUTOMATIC WASHERS
Amana
ALW410DAW
Washer - Top Loading
Amana
ALW410DAW-PALW410DAW
Washer - Amana Washing Machine Model ALW410DAW-PALW410DAW (ALW410DAWPALW410DAW, ALW410DAW PALW410DAW) Parts
Amana
ALW430RAC
Washer - Top Loading
Amana
ALW430RAC-PALW430RAC
Washer - Amana Washing Machine Model ALW430RAC-PALW430RAC (ALW430RACPALW430RAC, ALW430RAC PALW430RAC) Parts
Amana
ALW430RAW
Washer - Top Loading
Amana
ALW430RAW-PALW430RAW
Washer - Amana Washing Machine Model ALW430RAW-PALW430RAW (ALW430RAWPALW430RAW, ALW430RAW PALW430RAW) Parts
Amana
ALW432RAW
Washer - Residential
Amana
ALW450QAC
Washer - Top Loading
Amana
ALW450QAW
Washer - Top Loading
Amana
ALW450QAW-PALW450QAW
Washer - Amana Washing Machine Model ALW450QAW-PALW450QAW (ALW450QAWPALW450QAW, ALW450QAW PALW450QAW) Parts
Amana
ALW480DAC
Washer - Residential
Amana
ALW480DAC-PALW480DAC
Washer - Amana Washing Machine Model ALW480DAC-PALW480DAC (ALW480DACPALW480DAC, ALW480DAC PALW480DAC) Parts
Amana
ALW480DAW
Washer - Residential
Amana
ALW480DAW-PALW480DAW
Washer - Amana Washing Machine Model ALW480DAW-PALW480DAW (ALW480DAWPALW480DAW, ALW480DAW PALW480DAW) Parts
Amana
ALW540RAC
Washer - Residential
Amana
ALW540RAW
Washer - Residential
Amana
ALW540RMC
Washer - Residential
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
Brake Pad Kit
$ 55.81
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.