Brake Pad Kit

PartSelect Number PS2165432

This brake pad kit contains three brake pads and six installation screws. Helps to bring a rotating cycle to a stop.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not agitate.
  • Compare At

    $33.80
  • You Save

    $5.63
  • Your Price

    $28.17
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Silicone Grease - 2oz Tube

Part Number 2027573

$26.19
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.7 / 5.0, 8 reviews What's this?
1-8 of 8
 

9 of 12 people found this instruction helpful

Parts Used

  • Brake Pad Kit

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsSocket set, Wrench set

CustomerPeter from Littleton CO

Washing machine made squeaking noise

Brake pad kit does not come with installation instructions even though it says it does. Remove bottom front panel from washer. There are three brake pads. One of mine (the right one) broke into three pieces and was found on the bottom of the washer. This is how I identified what was wrong. Run the washing machine on the handwash extra light cycle (you could use another cycle, I used this one because I believe it is the shortest), there is a point in the cycle where the disk clamping the brake pads separates from the brake pads and allows you to remove and replace the pads. During other parts of the cycle, the disk is clamped onto the brakes and you could not remove or install a brake pad. I removed the two black hose on the bottom right to get to the right brake pad. Have a 2 gallon bucket ready to collect the water if you did run the washer as above. With difficulty, I was also able to reach around the back side of the right brake pad. I used a socket wrench set. I then removed and replaced the left brake pad. I left the rear brake pad in place. I was not able to get to it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used

  • Brake Pad Kit

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

Customerdaniel from angola NY

2 problems caused by bad brake discs

I first unplugged the washer. I removed the 2 screws that hold the front panel and removed the front panel, they are located at the very bottom outer edges of the front panel.
I then removed 4 of the large springs that are attached to the drum, this washer has six but I only removed the front 4. Removed the two hoses going to the water pump and drain hose, removed 4 bolts that attach the motor to its mounting bracket. Unplugged the wiring harnesses going to motor and what looks like a capacitor mounted to the side of the motor.Then I removed the drive belt. ( when the machine would first start to spin it would make a clacking noise which ended up being a chunk out the the drive belt causing the belt tenshioner to slap causing that noise and letting the drum spin during the wash cycle. So far very easy. I then removed the motor and when it is disconnected you can then remove the water pump. Three hex head bolts need to be removed and it pulls right off. I then removed the six bolts that hold the brake pads in place. I applied silicone grease to the new brake pads and installed them. The pad at the back of the drum was very hard to line up with the holes. I used a very small screwdriver to line up the disc brake mounting holes to get the bolts started and it worked fine. I then put it all back together and it works great. I have to add that I have been an auto mechanic for 28 years and not to brag but this is not your average repair job.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsWrench set

CustomerAlvin W. from Reidsville NC

The agitator moved in slow motion at regular setting

took off the front cover.
disconected the wiring from moter.
removed the motor.
replaced the brake pads one at a time used a flat screw driver to spred the plates apart.

The Plasatic Helix Drive Lup
took bolt at the botom of shaft off
this released the Helix drive lug.
took old lug off and inatalled new
replaced bolt and washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Brake Pad Kit

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Socket set, Wrench(Adjustable)

CustomerGARY from VILLA RIDGE MO

Tub would not stop spinning--brakes broke from bolts

Unpluged electric, diconnected dicharge hose from wall drain, disconnected water lines from rear of washer and at wall hose connection, removed lower front panel, removed large front panel, disconnected hoses at motor(put towels at hoses to catch water leakage)THEN-took washer to the garage and tuned up side down. Removed front two tub springs, removed (4) motor bolts, removed electrical harness from motor, remove and replaced new brake pads. NOTE:brake pads need to be somewhat driven(pushed hard) into brake pad slots. Also it was easier to install the rear pad by removing the 4" knock-out at the side of the washer. Somehow reinstall the knock-out to keep mice and animals from entering the interior of the washer. THEN- reinstall all items in reverse order. Any one mechaniclly minded can replace the brake pad. My wife and I saved lots by doing the replacement myself. THE END. Good job Gary Final note:besure to intall the drive "v" belt around the 2" pulley wheel.Very important.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Brake Pad Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerAlan from Shepherd MI

Brake pad was broken and spinning around making noise

this machine seems good to work on because almost every thing is done from the front without pulling it away from the wall. Removed front lower cover by removing two screws. There are three brake pads with two bolts each. applied silicone grease to each pad and put it back togather

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Brake Pad Kit

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsSocket set

CustomerJohn from North Kingstown RI

Washer was not agitating

Ipulled the front panel off and found that the brake pads had broken into pieces, ordered new pads. Two of the pads were accessed from the front of the machine and were relatively easy to replace by removing the two attaching bolts, spreading gap in area that they fit into with a plastic pry tool. I gained access to the third pad by removing the punch-outs on the side of the machine (circular). If I had not had these prepuched pieces available to me I would have simply cut an access hole in the rear of the machine with a jig saw, (who will ever see it).

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 14 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

Tools

CustomerJackie from Bel Air MD

Not spinning, making a loud noise

Unfortuantly this did not repair the machine. I beleive the transmission is gone and at this point it would be costly in time and money to repair. I went out over the weekend and purchased another Maytag (I just love this brand). It was on sale and I am also getting a rebate back from BGE for purchasing and energy star appliance. They will deliver this Saturday. I have spent some quality time with my sister doing my laundry at her house.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Brake Pad Kit

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerTimothy from Bowling Green OH

Washer would not agitate, but would spin.

Remove the lower access door in the front of the machine. Then I tipped the washer back against the wall to access everything. The pads are alittle hard to push in between the washer pulley disc. So I first pushed in an old broken brake pad off to the side, then was able to push in the new pads. The rear pad is the hardest and I had to release some of the front tub springs and remove the pump hose for access. Overall it went pretty smooth. Thanks for your help!Tim

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-8 of 8