2040953-1-S-Whirlpool-40047402-Plastic Helix Drive Lug
2040953-1-S-Whirlpool-40047402-Plastic Helix Drive Lug 2040953-2-S-Whirlpool-40047402-Plastic Helix Drive Lug 2040953-3-S-Whirlpool-40047402-Plastic Helix Drive Lug

Plastic Helix Drive Lug

PartSelect Number PS2040953

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Compare At

    $28.69
  • You Save

    $4.78
  • Your Price

    $23.91
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.7 / 5.0, 4 reviews What's this?
1-4 of 4
 

14 of 19 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerRalph from Moreno Valley CA

Unusually loud rumbling in spin mode, no spin out

removed outer enclosure to expose inside workings. removed all retaining springs to tub and transmission housing. Inverted tub to access agitator pulley and belt. Removed pulley and cut belt off.(I knew I was replacing it, anyway.)Had to remove large tub bracket to exchange new pulley for old. Disconnect bleach reservoir filler tubing on tub assembly. Disconnect power connector to drive motor. Removed water pump to access drive pulley where new belt belongs. Aligned belt to pulleys and checked idler pulley tension which was acceptable. Replace helix drive lug against spin/agitator and tightened retaining bolt. Assembled components in reverse order and conducted test run. Success. Smooth running machine and saved about $200 on professional labor costs. I had no repair manual but you should have a personal confidence in general repair work. Something like a history of taking things apart and putting them back together successfully. I had an independent appliance repair guy examine the washer and he said it was too complicated for him. Once I had it apart, it seemed fairly basic. Good luck!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsWrench set

CustomerAlvin W. from Reidsville NC

The agitator moved in slow motion at regular setting

took off the front cover.
disconected the wiring from moter.
removed the motor.
replaced the brake pads one at a time used a flat screw driver to spred the plates apart.

The Plasatic Helix Drive Lup
took bolt at the botom of shaft off
this released the Helix drive lug.
took old lug off and inatalled new
replaced bolt and washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerSteven from Lyndonville NY

Loud noise/washer tub doesn't spin

First remove the bottom front access door. The helix drive nut and pulley were both chewed up. I pushed the pulley up into the brake assembly to make sure it released properly. Mine released and the drum spun freely (I had my 8 yr old assistant turn the drum first). The helix nut turned with the drum so I assumed the transmission was good to go. Once my drive nut and pulley came in (two days), [UNPLUG WASHER AND DISCONNECT WATER] I took the top front cover off and lifted the top up and back on it's hinges. Next I disconnected the motor wiring harness, the bleach tube, the fill hose, the six drum springs, and the drain hose from the pump. Pulled the drum out of the shell and flipped it upside down. I took off the helix drive nut and removed the 8 bolts that hold the "milk stool and bearing assembly" and motor to the drum, also 2 screws that go into the plastic reservoir. I raised the milk stool enough to get the pulley out. (Belt was good) Put in new pulley and pushed the milk stool back down. (I was careful to keep the bearing on the shaft splines). Put the belt back on the pulley and idler. Put in all the bolts and put back together in reverse order. I recommend starting with the back drum springs, that's how I did it and it was easy. About an hour. Good luck.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 14 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

Tools

CustomerJackie from Bel Air MD

Not spinning, making a loud noise

Unfortuantly this did not repair the machine. I beleive the transmission is gone and at this point it would be costly in time and money to repair. I went out over the weekend and purchased another Maytag (I just love this brand). It was on sale and I am also getting a rebate back from BGE for purchasing and energy star appliance. They will deliver this Saturday. I have spent some quality time with my sister doing my laundry at her house.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4