Timer

PartSelect Number PS2019611

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not drain.
  • Will not agitate.
  • Compare At

    $151.98
  • You Save

    $25.33
  • Your Price

    $126.65
In Stock
Order within the next 11 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.7 / 5.0, 5 reviews What's this?
1-5 of 5
 

11 of 12 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerVirginia from Parma OH

Washer quit cycling through all the wash and rinse steps

First removed two screws holding control panel,once those are out, you remove the center plastic on the selector button,remove the metal retainer and take the button off the outside of the panel ( be careful of the spring behind the button) Next there is two bolts screwed from the front that hold the timer in place,remove these and the timer is removed, unplug the electrical wire plug from timer and you have it . Just reverse the steps and your all done!!! easy repair! Maytag repair man wanted over 100.00 just in labor! I did it in less than 30 minute's and that was just trying to find some tools.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerSteven from Chatom AL

After 13 years, the timer on our maytag washer just "wore out".

I received the part next day, just as promised. I removed two screws to take the top panel off the washer, removed the two screws on the old timer and put the new timer in. Had the repair done withing 15 minutes - I have replaced this before, I am 54.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerDeon from Bartonvill IL

Washer stopped spinning as well as drawning the water out.

First removed the cover off the control knob on the front of the control panel. Then removed the clip holding the control to the timer. Watch for the spring that is under the control knob as you pull it off. Then remove control ring set them aside. Next unscrew the two screws holding the timer to the control panel. Next unscrew the screws holding the control panel. Removed control panel. Next unfasten the wire harness from the timer. Remove timer and install new timer. Replace wire harness to new timer. Screw new timer to control panel. Replace control panel and screw into place. Replace control ring then timer knob with spring. Replace cover on control knob. Simple, Easy and Fast.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 10 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerWilliam from Fredericksburg VA

Timer caused failure of washing machine to complete cycle.

Removed timer, ordered par;t and, upon arrival installed timer -- washing machine works like a champ.

Easiest repair I've ever made.

Respectfully,

W. E. Akin, Jr.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerBrian from Medina OH

Timer quit working

REMOVE CAP ON THE KNOB, REMOVE CLIP UNDER THE CAP. PULL OFF THE KNOB AND BEZEL. REMOVE FOUR SCREWS ON TOP OF THE CONTROL PANEL TIP PANEL FORWARD & REMOVE TIMER SCREWS. DISCONECT WIRING PLUG FROM OLD TIMER. VERY SIMPLE OPERATION.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5