Models > LAT8005AAE

LAT8005AAE Maytag Washer - Overview

Get Parts and Repair Help for LAT8005AAE

If you know the washer repair part you need, you can browse the list of all parts on the LAT8005AAE, or you can search by name or part description. You can also find your part by where it is located on the LAT8005AAE by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LAT8005AAE parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$12.42

Drive Belt

This rubber V-style drive belt drives a washer's transmission.

$16.64

Pump Belt

This V-style pump belt is typically used with washing machines that use two belts. This belt is about 40.5" long and 3/8" wide. This pump belt helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.

$2.70

Screw

This screw is sold individually.

$60.14

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.

$17.13

Dryer Door and Washer Lid Switch Kit

This kit is simple on/off mechanism that prohibits the machine from operating when the door is open.

$48.61

Drain Pump

This assembly uses 2 belts. Order belts if you notice wear and tear.

$2.70

Hose Clamp

$33.45

Lid Switch Assembly

This black lid switch assembly comes complete with a bracket, two switches, and a fuse. An open fuse might indicate that the lid switch is bad. The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.

$2.70

Screw

This screw is sold individually.

$32.43

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 304 of 314 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Leaking water

  • Customer: Joseph from Plano TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 98 of 111 people found this instruction helpful
Well, I found the washer leaking water from the bottom a couple weeks ago. I finally got around to pulling off the front panel and ran a couple cycles to see where the water was coming from. Turns out the leak was at the plastic pump that does the draining after wash and rinse.

So I got the model number and googled online. I found Partselect an... read more

washer would not start

  • Customer: Peter from Westbury NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 81 of 98 people found this instruction helpful
To see if the lid switch was the problem I first jumped it out and tried to start the washer. That was the problem. I removed the main controll so I could get to the lid switch. I made the mistake of removing the screws all the way out and the metal clip fell into the body of the washer, no problem since I was changing the drive beld anyway. I realized that ... read more