Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LAT5005AAW

LAT5005AAW Maytag Washer - Overview

Get Parts and Repair Help for LAT5005AAW

If you know the washer repair part you need, you can browse the list of all parts on the LAT5005AAW, or you can search by name or part description. You can also find your part by where it is located on the LAT5005AAW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LAT5005AAW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$24.68

Belt Kit

This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these bel...

$3.02

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

$52.96

Mounting Stem/Tub Seal Kit

This kit comes with a hub assembly, agitator seal, and spanner nut. If your washer leaks once it is full (with or without clothes in it) or leaks during agitation, then you should ...

$6.08

Rubber Foot Pad

The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers. Many of our customers have rated this repair as very easy. To complete the repair, turn the old leg counter clockwise to remove it. Then, simply remove the old pad and replace it with the new one. Finally, re-attach the leg by turning clockwise. Ensure that the washer is level, and adjust the leg accordingly if it is not.

$3.77

Centering Spring

This centering spring is nine and a half inches long. It is a metallic spring.

$19.19

Lid Switch

This 3 prong lid switch is used for washing machines that do not have a tub light.

$5.05

Washing Machine Lid Hinge Ball

This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plasti...

$45.89

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time. The tub bearing kit fixes issues with leaking, loud noise, excessive shaking/moving or if your pump is not spinning. The tub bearing kit is fastened in the middle of the outer tub of your washer. The tub bearing ensures the inner tub is spinning effortlessly. If the rub bearing is faulty it might lock up and cause the washer to stop spinning. This is an OEM part that is obtained straight from the manufacturer.

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$22.81

Damper Pad Kit

This damper pad kit is used for base support. It comes with three six inch damper pads, two little tubes of lubricant. NOTE: This part will need adhesive to stick it in place.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 460 of 470 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 336 of 177 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more

Damper pads wore-out and had metal to metal contact which caused the washer to spin out of balance.

  • Customer: Steven from Rockford, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 129 of 148 people found this instruction helpful
1: Disconnected all water and electrical connections.
2: Removed front panel.
3: Disconnected all wires leading from the control panel and removed the top of the washer.
4: Removed the springs that holds the drum down on the damper pads.
5: Flipped washer upside-down so the drum would hang from the bottom of the wash. This made it easy ... read more