Snubber Ring

Followed instructions and needed help lifting drum out but no problems. Parts fit perfect and unit is as smooth as new.

Washer was shaking/thumping during the spin cycle for even the lightest loads. Previously changed the suspension springs, and the problem was not resolved.

I was able to locate the service manual for this washing machine online and download the PDF for free. Getting this will provide dis-assembly instructions and photos.

Sorta like requiring that you disassemble an engine in order to change the oil filter. Engineering suggestion here for any Maytag folks cruising the site. Mount the snubber ring with it's own clamping ring so that you can change it (snubber) without removing the agitator & spinner basket from the tub. Think something like this... Remove suspension springs, remove hoses, flip entire assy. upside down, then replace snubber ring without any further dis-assembly.

I followed the service manual's recommended approach, here are the basic steps:

1) Open the small back cover and detach the wash drum's drain hose at the waste pump, and while you've got back of the unit visible, tip forward and unhook the drive belt from the motor, pump and agitator.

2) Use a spatula or putty knife on the front seam between the lid and the lower body to unlock the spring latches which keep the top on. Flip the top up and back to get into the basket area. Take off the front cover so you can see the wash drum.

3) Remove the top cap/splash guard around the wash drum by pressing the cap/splash guard down while unhooking the little ears.

4) Remove the fabric softener cap from the center of the agitator and remove the bolt that's down the center of the agitator. This will require a socket. Remove agitator and plastic skirt that goes around the bottom of the agitator.

5) Remove the plastic sealing nut. This nut has a number of small plastic points on it and I broke a number of them off with the channel-locks while removing this. You may need to order a spare.

6) Remove the washing drum.

7) Use the spanner to remove the basket hub. I made a spanner out of some scrap steel parts I had and mounted using the screws I took out in step 5. If you have a spanner, you're set here.

8) Unhook the suspension springs and you should be able to lift the entire unit right out of the base.

9) Remove the cap on the bottom pulley and pull the E-clip that holds locks the pulley in place. Remove the pulley and plastic gears which mesh with the transmission shaft.

9) The snubber ring (the problem here) is located under the brake plate/ring on the very bottom. The brake assembly is preloaded with a spring inside, the manual says to use a special spring compressor while assembling. I didn't have any trouble holding it down while I had my 5 year-old daughter start the screws for me. Remove the 6 small screws around the brake ring and remove the shards of the worn out snubber. Replace with new snubber and start re-assembly.

Possible Shortcut:

After doing this, I see it may be possible to shortcut the factory directions. I can't guarantee that it will be successful, but after doing it I don't see any reason it wouldn't work. Following above numbers:
1) Do numbers 1-3 above.

2) Jump to step 8, remove the suspension springs and just get the entire drum removed and inverted. Don't mess with the legs, don't mess with the attachments or anything. You will only need to work on the pulley.

3) Remove the drive pulley and brake retaining plate. Shouldn't need to do anything with the inside of the washing drum here. No need to mess with the seals and/or plastic nuts.

4) Replace snubber and reassemble.

took drum out replase snubber put drum back in

I took out the agitator first, then I took out the inner tub, next I took out the outer tub, and last I took out the transmission assembly. After replacing the snubber I put the transmission assembly back on, then the new outer tub and next the inner tub. Last I put the agitator back on.

watched youtube on how to change out the snubber ring. it was quite easy.

First of all..the helpful hints from all with the problem is appreciated..I had a problem stretching the spings to connect..but other than that..because I am a senior..it was kind of difficult moving the machine around....but it is done..and there is a difference..I thank you all for your help and info..

got the right part great service from partselect invited my bro in law 20 mins we where done.. no more violent shaking spin cycle thank you very much

After unplugging washing machine, I lifted the top to access two screws that held on front of machine. I removed the old springs with vise grips. I removed the two screws holding the motor to remove the drive belt then the drum could be lifted to replace the snubber. Drop the drum back down and tilt the machine back so the drive belt can be placed back on the drum, motor and water pump pulleys. Reinstall the motor screws. Install the new springs, this can be difficult, I used a board to stretch the springs. Put front back on and do your laundry.

found your web site and the helpful hints Thank you it works wonderful even washing heavy loads