Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11747089
Handle only available in black now. Latch sold separately.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Managed to open the dishwasher without breaking anything else! 1ST TURN OFF THE POWER SUPPLY AT THE BREAKER BOX,SAFETY IS PARAMOUNT! Took the kick plate off at the bottom, unscrewed the bottom of the front panel and removed the interior door screws. Removed top panel with the circuit board attached, be very careful doing this as you can destroy the circuit board if it cracks or bends.Unplug it and set it aside. remove the broken door handle and insert the new one with the simple metal and spring mechanism. put it all together in reverse order. DO NOT OVER TIGHTEN ANY OF THE SCREWS OR YOU CAN STRIP THEM AND HAVE MORE PROBLEMS! I have to say I was surprised how quickly the part arrived during some of the worst weather conditions up north. Very pleased!
Help other customers find the most helpful instructions.
Were these instructions helpful?
Normal handle replacemnt would have been by removeing the screws on the inside panel to release the front panel and permit access to the handle location. The door being latched closed required aceesing from the exterior by removing all of the outer screws and outide panel, removing all of the interior components and then reaching the latch from outside. A most difficult process. Some other plastic clips were broken in this process. Once the door latch was released, normal acces was easily gained and replacing the handle was relatively easy. After everything was reinstalled, the top outside pane was loose because the broken clips no longer held the panel in place. A self tapping screw, although visable but not too noticeable, holds the panel secure.The unit is over 11 years old and plastic is not very durable. The handle was subject to being broken by normal everyday useage. A metal part would have been much better a design for this item.
Took 6 screws off to disassemble the control panel, removed the electonics, removed and ordered handle, and replaced it.Smooth.
Removed inside cover and inserted new handle on two tabs and attached latch. Slightly tricky to get 3 pieces in place and reattach cover without them moving.
Uncscrewed the lower washer arm retaining nut and replaced it along wint the 2 washers. Cleans like new.Unscrewed the front panal from behind. Removed the inside vent covering. Unscrewed the handle screws and removed the handle. Replaced the handle and screws but not before gouging the back of my hand ( I had a needle and thread) and then reattached the panal and vent cavering. The blow-up diagrams you all have are a great reference. Thanks
remove the top 4 screws, tilt out, pull up and away from door. remove screws holding circut board. lay panel on counter and remove metal rod and put in new handle, it can only go one way. install handle into panel and snap in place. reinstall circut board, slide bottom of panel in first, reinstall 4 screws.15-20 min job. I also installed a new cover over the front panel because the old one was bad.
After throwing a fit- I looked on the internet for any drawings from the Kitchenaid website. There were none. I then started taking apart the dishwasher, took apart the entire front door. Found that the door handle was broken and went online to find the part. Partselect.com had the drawing of the door assembly, realized that I didn't need to take apart the whole door! Reassembled the door while waiting for the part, then using the partselect drawing, removed only the parts necessary and replaced the broken part!
No repair just changing color. As a women I went online and ordered all the parts I thought I would need and they arrived within a few days. Everything went together perfect. We used the parts list from online. First time everything was right and worked perfect. My husband put everything together and I kept my fingers crossed.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.