1015726-1-S-GE-WR02X12149        -Compression Ring
1015726-1-S-GE-WR02X12149        -Compression Ring 1015726-2-S-GE-WR02X12149        -Compression Ring http://www.partselect.com/Schematics/GE/GE_Thumb/00119164i06.gif

Compression Ring

PartSelect Number PS1015726

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Noisy.
  • Freezer section too warm.
  • Fridge too warm.
  • Compare At

    $1.88
  • You Save

    $.31
  • Your Price

    $1.57
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 18 reviews What's this?
 

35 of 63 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerDaniel from MIAMI, FL

Loud whinning noise of fan in freezer section

1. content of freezer was put in an ice box
2. panel covering rear of freezer compartment was removed, a few screws
3. old fan now accessible was removed an new fan mounted.
4. modular wiring plug broke, wires had to be soldered and wrapped in heat shrunk insulation
5. compartment was cleaned an rear inside panel closed

Thanks for all those who shared their experience and the schematics available on website. It gave me the confidence to to this myself. Its my second repair in freezer (previous being a defective heater)

Help other customers find the most helpful instructions.

Were these instructions helpful?

35 of 73 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerGuy from New Palestine, IN

I placed a heat gun in the freezer section to defrost the coils and did not return in time. The heat from the heat gun rose upward and melted all of the soft plastic parts. The good news was that the 16 parts were not expensive but the one main part that was needed to put it all back together took 3

I replaced all of the plastic parts as well as the heat coil that is mounted at the bottom of the coils that keeps the coils from freezing up. If I had not melted the plastic parts the coil could have been replaced in 2 days, 1 day to receive the part and the next to do the work. This is the second time I have had to replace this heater.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 21 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerBert from Audubon, PA

High pitch noise

My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 22 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerEugene from Marion, TX

The condensor fan in the unit appeared to have been chewed by a mouse and would not function and the lower door was too low.

The condensor fan in the unit appeared to have been chewed by a mouse and would not function. We had a service call to verify this and ordered the parts. Delivery was extremely quick and we were able to complete the repair and place the unit back into service within 2 hours.

All that was necessary was to remove the bottom cardboard cover, replace the fan and grommets, and replace the door bushings.

Thanks!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 15 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerSteven from Columbus, OH

Motor vibration

I pulled the inside cover in the freezer off, pulled the motor out of the bracket, replaced the fan blade , motor, and grommet and that was pretty much it. Very easy to replace. Parts select was fast and had the cheapest price available.
Thanks
Steven Roffey

Help other customers find the most helpful instructions.

Were these instructions helpful?