Models > ZISW48DWA

ZISW48DWA General Electric Refrigerator - Overview

Get Parts and Repair Help for ZISW48DWA

If you know the refrigerator repair part you need, you can browse the list of all parts on the ZISW48DWA, or you can search by name or part description. You can also find your part by where it is located on the ZISW48DWA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ZISW48DWA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$6.20

Dispenser Door Assembly or Flapper

This part mounts in the ice dispenser. **** The crank no longer comes with this part. You can use original crank. The crank is sold separately depending on model number of appli...

$137.62

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

$33.30

Dual Inlet Water Valve

This valve comes with 1/4" compression inlet. NOTE: This part comes with new quick connections. To install - cut retaining nuts off of existing plastic water lines and gently push...

$3.22

SWITCH LIGHT

$5.79

Water Tube Union - 5/16" x 5/16"

Sold individually.

$73.67

Dispenser Control Board - 2 Slide Switches

It is used with those refrigerators that have an ice and water dispenser in the door.

$136.36

Auger and Ice Bucket Assembly

This auger and bucket assembly is used on 25 cubic feet and 27 cubic feet side by side models.

$47.63

Defrost Timer

This refrigerator defrost timer will cycle for twenty-five minutes after every six hours of run time. The timer itself is made of plastic, and its terminals are bent, the leads are internal, and the label is orange.

$7.27

Actuator Pad

$59.37

Solenoid and Arm Assembly - 120V 60Hz

This solenoid and arm assembly is for the cube/crushed ice.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cracked housing on the vaave

  • Customer: anthony from thornton CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 185 of 202 people found this instruction helpful
1. Turn off water supply, and electrical ( unplug it) to fridge.
2. Remove water line to valve. Watch for water to pour out of the line. Have a towel handy.
3. Remove the cardboard cover on the bottom of the fridge.
4. Remove the screws that hold the valve in place.
5. Remove the valve, be careful the waterlines are still attached.read more

Ice cubes do not dispense because auger does not turn. Bad switch on control board.

  • Customer: Michael from Allen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 61 of 65 people found this instruction helpful
1) Turn off water line and unplug power.
2) Pop off front panel plate at ice cube select switch area.
3) Unscrew 4 screws that holds control panel housing in place.
4) Remove panel assembly by disconnecting two different wiring plugs.
5) Unscrew 2 screws that allows access to control circuit board at end cap.
6) Remove circuit board ... read more

ice stalactites were drooling out of the icemaker and gumming up the cubes in the receiving tray.

  • Customer: Gerald from Benicia CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 40 of 42 people found this instruction helpful
I first shut off water flow to the fridge. Examination of the package (which was not exact in appearance to the original) demonstrated that the electrical connectors were well-insulated so I arrogantly and successfully proceded without disconnecting the power. My fridge is old enough that the model doesn't appear exactly on anyone's list so I wasn't alarmed... read more