ZISW42DYA General Electric Refrigerator - Instructions

I removed the front of the unit assembly and removed the entire auger unit and drive assembly. I married the old drive cup and new drive cup back to back using vise grip pliers, drilled 4 3mm holes, installed 4 phillips head stainless steel screws and, using an emory wheel, ground off the exposed screw ends. I then re-installed the drive assembly and auger unit. This increased the length of the drive cup allowing the drive to fit without any slippage. The entire cost was less than $18.00 including shipping and screws and took about 1 hour. It works great.

Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.

My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.

Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrigerators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.

Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.

Literally took out one screw and a wiring harness. Removed the old plastic piece off of the old ice maker and put on the new one.Installed new ice maker with the one screw and plugged the wiring back in.DONE!

installed new dispenser control board. pretty easy. just make sure the actuater is snapped back properly or ice/water will not stop dispensing

Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.

Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen

I noticed water leaking from the bottom right rear of the fridge. I figured it was from the ice maker feed as I don't have the ice water feature on this GE profile. I shut the water supply off, ordered the part and received it in a few days. The defective part was easily accessible after I removed the cardboard cover. I removed the copper feed and unscrewed the old valve with a nutdriver. The new part fit perfectly, and even though there were instructions in the part to use the old bracket. the plastic water feed fit into the ice maker compression fitting with ease. I ran into a problem when I re-installed the copper compression fitting on the new valve,as I could not stop a leak from the top of the compression fitting. When my plumber originally installed the copper line he used enough pressure to deform the compression sleeve that slips over the copper tube. I had a couple of them in my "parts" drawer, so I took my tubing cutter and took 1/2" of the end of the copper supply line; slipped the new sleeve and re-installed the compression nut over the valve....fit perfectly. Turned on the water supply; no leaks. Checked the icemaker about 4 hours later and it made the first tray of ice. If I didn't have to deal with the water supply leak at the fitting, the job would have been finished in 30 to 45 minutes.

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

I had to defrost the freezer to free the icemaker. After that the installation was plug and play with two small exceptions: 1) I had to file down the width of the left hand tine of the old stripper so that it would fit the new icemaker, and 2) the motor housing of the new icemaker was slightly wider than the old one. It fit, but just barely. But I'm back in the ice again, no dripping water, all is good.