ZISB36DRC General Electric Refrigerator - Instructions

Observing the ice maker itself was working, and that water was flowing to the dual inlet water valve, I assumed the problem must be a faulty outflow valve. If either of the two valves do not close completely, the water slowly accumulates in the plastic line and freezes as it enters the freezer compartment. A solid plug of ice will form in the line, either causing no water to enter the ice tray, or it may leak under pressure when the valve opens briefly (as was my case). The solution was simple: change the dual inlet valve, and while this took me approximately 15 minutes to 1)turn off electricity and water to the frig, and 2)replace the part, the plastic tube going to the ice tray warmed up enough as I watched a one inch plug of ice exit the tubing. Once the power and water was turned on, and I checked for leaks, the ice maker worked like new! Not bad for a $30 fix.

Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.

Shut off water & elect to refg. moved refg out from wall. Removed back cover. disconnected water & electric connections. Removed old valve and installed new one . Plastic tube fit in same place elect pins (4) snapped in place. Used teflon tape when connecting copper plumbing to stop leaks. Also cut old tubing & replaced copper 1/4" compression ring. Note I ordered part before noon on thursday, part arrived fri AM 9:00 FedEx.reg service. cleaned up mess picked up tools. Refg worked like new. saved money on service call. Thanks

Unplug the refrigerator. Remove the bottom panel the locate the valve on the left side of the refrigerator. Remove the valve. Unplug the two electrical connecters, then remove the two water lines. (At this point there will be a little water escape). Then replace the lines in the new valve, replace the electrical plugs and reassemble the bottom panel.

followed the previous posts, loosened four screws on the front panel, attached panel to new auger and ice bucket, and was good to go. Excellent advice!

watched a 2 minute video on installing the connector. Then using the utlity blade cut out a 1/3" section of the tubing and installed the connector. DONE! Leak fixed

remove ice bucket and replace broken augar

remove 3 bucket screws. 1 bracket screw slide bucket back insert drive reverseb steps

It was exactly as shown in your instruction video

Ice bucket and auger came fully assembled. Just had to attach the face plate from the broken ice bucket assembly and slide it into the freezer. There were only four Phillips screws involved.

Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

Recently changed the "under the sink" water filter because ice was getting really small-the filter was old. Ran great for a month or two. Then.....no ice. Water pressure ok. Even filled the ice tray in the ice maker and when frozen it kicked it out.....but no more. Repair took 15 minutes......pretty easy. When I called local appliance repair......they estimated it would cost $200-$250. My part was $44.

I removed the front of the unit assembly and removed the entire auger unit and drive assembly. I married the old drive cup and new drive cup back to back using vise grip pliers, drilled 4 3mm holes, installed 4 phillips head stainless steel screws and, using an emory wheel, ground off the exposed screw ends. I then re-installed the drive assembly and auger unit. This increased the length of the drive cup allowing the drive to fit without any slippage. The entire cost was less than $18.00 including shipping and screws and took about 1 hour. It works great.

Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...