ZBD6890K03II General Electric Dishwasher - Instructions

removed defective axel and wheels installed new ones

Replaced the part by taking off the srews on the inside of the dishwasher door (all of them)to get to the backside of the soap dispenser. Remove an electrical connector by pulling (had to pull off using pliers as it was really on there). Then a couple of screws hold to to the inside of the door. Pretty straight forward.

After determining that the leak was coming from the sump connector, I had to completely remove the unit from the counter. After removing all the parts in the wash cabinet (wash arms,conduit,fine,course and sump filters),the sump connector nut was revealed which I loosened, but did not remove, with a channel lock plier. The unit was then placed up-side down where I then loosened all the worm clamps that attached the drain motor,pump,and turbidity sensor to the sump and sump connector.then I removed the brackets that braced the pump to the washer body and removed the pump.at this point,you should be able to remove the drain motor and turbidity sensor from the sump and remove the sump from the washer. You should also be able to remove the connector as well.Both these items are made of some type of rubber which seems to deteriorate from the soap which was caked all over them in my case. Just reverse the above process to re-install everthing. I didn't find this job terribly difficult and it was certainly better than spending hundreds replacing the unit.

Installed new rack assembly and it works fine. Thanks

Opened dishwasher after it completed a wash cycle. Found the rinse dispenser cap had come off during the wash and melted on the heating coil at the bottom of the machine. Pulled cap off of coil, made sure coil was not disturbed. Looked in various sites for cap. Finally found this site where I didn't need to order the whole mechanism and could order just the cap. Received the cap, screwed into the dispenser, fixed. The only problem I had was that there were two possible caps so I picked the one that was the same color as the original one. Project completed. Thanks

removed original rack, inserted replacement.

Removed old wheells replaced with new whells. Very easy to fix. Quickly received after order.

Bought new wheels & wheel axels. Very simple to replace (no tools required). New wheel axles much better desigh,

Came home for lunch to discover the kitchen rug soaked and the dishes I had started when I left that morning unclean. Not sure what happened, pushed start again and immediately found water flowing out from under the machine. pulled the machine out and discovered that mice had chewed through the pliable vinyl sump tank. found the part number in my owners manual and google turned it up on Part Select. this was on Saturday and I had the part Tuesday. very satisfied

After replacing the wheel and axle assembly once, I decided this time to instead just replace the axles with the new ones with improved design. Removed the wheels, pulled out the old axles and put the new ones in. Simple

Popped the wheels onto the wheel axle and let my 7 year old snap the completed assembly onto the lower rack. So easy, even a 7 year old could do it! Total cost of $28 to replace all 8 wheels, which had degraded over time. Lower rack now rolls in and out perfectly. The design for the replacement wheel axle is slightly different than the origional, so the suggested part is the right one, even though it looks a little different from what the dishwasher came with. I am now a happy girl and don't have to fight with my dishwasher any more!

Get parts axles and wheels snapped together well.

put new part on by looking at other side no directions with parts

The rear wheel on the lower dish rack broke at the axle attachement. The wheel then feel inside the dishwasher against the heating element causing the wheel to melt. I ordered the new parts and they arrived very quickly. I attached the axle to the wheel with hand pressure, no tools required. I then attached the wheel assembly to the verticle support of the lower wash rack with hand pressure and was done. Very easy and the new design of the axle seems to attach better to the rack.

The orginal axle design was terrible. The old axles broke and fall off. The new axles snap on with moderate force but the keep the wheels on now. The Rack works perfect now!