Models > ZBD6880K10SS > Instructions

ZBD6880K10SS General Electric Dishwasher - Instructions

All installation instructions for ZBD6880K10SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ZBD6880K10SS
76-90 of 290
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

soap dispenser was not staying closed....

  • Customer: Erin K. from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
hubby had no prob replacing the new part!!YEA!!dishes are clean again!

Wheels kept coming off dishwasher basket upon pull out

  • Customer: Glen from Garland, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
I hand removed the snap in wheel axels and replaced the axles with new ones, by hand, no tools needed. On this dishwasher basket the wheeel axels just snap onto the metal cage "wires" of the roll out basket holding the dishes. Very simple. Used pliers to squeeze each old axle retaining nubs,from each of the eight wheels, , then just slipped (pulled the wheels off the axles) and discared only axles (that here the problem, detaching frequently from grasping the pull out dish basket, due to heat taking the temper out of their gripper (to basket).

Soap Dispenser latch broke

  • Customer: Vicki from Mooresville, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
I removed six screws and unplugged the module and removed.
Replaced by the new module and plugged in and then replaced the six screws.
Very easy to fix.

wheel axles broke off from lower basket--deteriorated from age and almost daily use of dishwasher

  • Customer: harry from west seneca, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
old axles were removed by pulling wheel assembly from lower basket pins. squeezed old axle with needle nose pliers and discarded broken wheel axle. snapped wheels in place on new wheel axle and snapped wheel assembly into place on the basket. i replaced only two axles since the remaining ones were still intact. actual repair time was under three minutes. if all eight wheels would have to be replaced, i'm positive it would have taken no more than five to six minutes. in fact, the new wheel axle is a much better design than the original.

Lower rack jamming and hitting washer arms

  • Customer: Matt from Simi Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I first tried the local appliance shop i got the wrong parts twice. I then wrote the model and serial #'s of my unit and found parts select. Got the right parts quickly and all I had to do was pull the old rack out and slide the new one in. Viola she was done ! Thanks Part Select !
Matt Hansen

Broken axle on one wheel

  • Customer: Andrew from DeWitt, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Only one axle was broken, but I replaced all 8 because GE had redesigned the axle to prevent future problems. Decided to just replace them all and be done with it. Took 10 minutes, start to finish and all is well.

The wheels kept falling off the bottom rack of the dishwasher

  • Customer: Suzanne from Oak Ridge, NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
My husband took off all the wheels and changed the axles. We had friends who had the same problem and they led us to your web site.

Needed new wheels

  • Customer: Jason from Omaha, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I inserted wheel axle into wheel and attached to bottom rack axle. It was simple. No problems.

soap dispenser latch was broken & didnt shut

  • Customer: julie from Saint Charles, MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
We had to replace the soap dispenser. My husband is not very handy & this was a snap. You take off the front panel (cover) of the sishwasher & simply unscrew the old one & screw in the new one. I probably could have done it myself.

Needed to replace original wheels on bottom rack

  • Customer: Farrell from Grass Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Very easy job. Just took out the bottom rack and replaced the wheels that kept falling off. A no brainer! works wonderful now. Most impressed with the ease of ordering and amazed how quickly the parts were delivered to me. I saved alot of money doing it myself! Thnak you

three lower tray wheels broken

  • Customer: Mark from West Point, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
Used plier to pinch the axle head to take the old wheels off then pushed the new wheels on by hand.

Axle attachment breaks on lower rack

  • Customer: Marc from Sebastopol, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
Remove all wheels on one side. Use pliers to remove broken axles from wheels. Pop in new axles, then go to lower rack and attach to rack by pushing axle pinch mechanism onto rack support. New axles do not look like old ones—they are improved.

The lower rack, front wheels kept falling off and getting melted on the element

  • Customer: Simon from Great Falls, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
We ordered 4 wheels and axels, took off the old wheels, assembled the new wheels by popping the axel into the wheel (really simple) and then snapping them onto the post. It was incredibly simple. We waited 3 days for the wheels to arrive,the mailing cost was more than the parts! The result is amazing, the lower rack now runs smoothly and sits inside the washer as it should do without falling down all the time. Well worth the small amount of effort to find the right part and much cheaper than buying a new one!

New wheels for lower rack on dishwasher.

  • Customer: Melissa from Vienna, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Ordered on a Friday and parts arrived Sat. No tools required. Pieces easily slipped into place. Dishwasher is all fixed. This site is much easier to use than GE's. Will use PartSelect for all future replacement parts.

Wheels keep falling off dish rack.

  • Customer: Jonathan from New York, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
So easy and the posts on the site were incredibly helpful in determing what part i needed. The wheels on the dish rack inside the dishwasher kept falling off. I had to keep lifting the dish rack in and out of the dish washer to load and unload it. Unbelievably annoying. I popped the old wheel axels out of the exisiting wheels and replaced them with the new wheel axels I ordered from PartSelect. Then I attached the wheels back on the dish rack and it was right back to normal.
All Instructions for the ZBD6880K10SS
76-90 of 290