YWSR2100T3WW General Electric Washer - Instructions

Replaced dual inlet valve. Problem solved

We bought this used Hotpoint that was probably one of the original machine created back in the stone-age, it's so old. We've had it 10 months, and it's always had this... burnt rubber stink to it... then one day, it stopped agitating and sounded like a metal bucket of bolts being shaken. We're on a military income with five kids, and the idea of buying a new washer was just... heartbreaking. On a whim, having fixed a washer once before, we opened the front up and painstakingly pulled every last rubber fiber from what used to be the belt. Ordered the part. It shipped quick, arrived quick, and in under a week we were back in business. Someone else had mentioned the needing 1/4" socket, and I was glad I remembered that, because it made is SO much easier.

I work in hvac, I more or less understand the older electro mechanical non electronic machines so I gave diagnosis a stab. I already knew that the water level switch could cause problems. I noted that the hot and cold water fill valve solenoids DID shut off tightly. While testing, I tried blowing and sucking on switch hose port and listened for a clear click; no click. At this point you replace the switch just to be sure. I blew out on outlet side of vinyl tubing going into water in tub. Used model and serial number to locate part on website. I physically removed water level switch (you twist it off by gently prying under a tab and turning 90 degrees) or else remove switch with short mini philips. I very carefully compared the removed switch visually to the very good multiple multi position photos on website. That showed me that the switches looked the same. So when I orderred the part I was 98% sure it was right. The part arrived and was correct. I installed it in 5 minutes, tested it with different levels. Machine repaired! Recorded part number in computer notes.

After figuring out to use a very small flathead screwdriver to get out the "star" screws holding on the front panel, since I don't have the proper tool for this, it was easy! Just disconnected hose lines from back of washer, unplugged the old valve, removed the screws holding it in. I disconnected the small water line that was connected to valve. I put in the new valve, reconnected everything, put panels back on, and it worked like new again.

Installed a new mixing value. Repair went quickly and easily. Repaired machine working great. Easy ordering and the prompt shipping impressed us Greatly!! Thank you!

at 1st, i call GE for service, but i have to wait for the next available field service engineer which is 7 to 8 days to come to my place to check on the washer. the cost is $99.00(non refundable) and then he will order the parts needed for repair another 2 to 3 days. then i decided to buy the parts myself online,and google the web on "how to fix the washer that stopped agitating" everythings in there,with video instruction. pull the agitator up and out by grabbing on to its base. inside, the knot was corroded and the o ring worn out,but really easy to remove with the 11mm socket. the coupling kit although looks different,fit perfectly. insert says its an upgrade of the old model. toss the old and replace with the new, no sweat! now it's shaking like crazy.

An older gentleman neighbor needed help finding a part for his machine. We checked local parts stores to no avail. I researched the internet, found your site and ordered the part. My adult son put the part on in less than 15 minutes. Our neighbor was very happy. We will tell any one in our neighborhood to order parts here. We followed the part watching UPS. The part arrived at the exact day and time. It couldn't be easier.

Removed the four torx-head screws on the top of the washer. Pulled the control panel forward. Removed the four screws on the back of the washer and the two screws that held the dual valve on. These six screws required a nut driver. Pulled the small hose off the old valve. Then reversed the procedure. Total time to replace the faulty old part was about ten minutes. With saftey in mind, disconnect the electrical cord and shut the water valves off at the wall.

Viewed the step by step how to and was able to complete repair all has worked well great info sight!

I followed the on-line video with just one exception and I had the old part off in less than 5 minutes. I ordered the part on Saturday afternoon and I had the part in hand by Wednesday morning at around 11:00 am. I spent less time installing the coupling kit than it took to take it apart and had 2 loads of clothes done before going to work on second shift. I would recommend anyone needing help contact Parts Select. They were great and very helpful.

The agitator is the tough thing to remove, I took a previous posters advice and used a rope and 2 boards to pull it up. I will describe it as many short ropes but it can be done without cutting the rope if you think a lot about it. loop the a rope under the agitator so its under 1/2, loop another rope under the other side. tie both loops so you can slide a board in each across the top of the washer. Then tie the 2 loops together on 2 sides down near the bottom of the agitator otherwise they will come out from under it when you pull. then slide the boards in the loops and lift up pulling up the agitator.That is the hard part. Remove the bolt on the coupling, and pull it off. The new one had to be lightly hammered on with a rubber mallet, then use the new bolt. the Agitator slide down and with a push down it popped on. Putting the new part on only took 15 min, removing the broken one took about 45 min. Washer is woking great now ! Saved over $100 or buying a new washer !

Pulled agitator by hand, (very easy), removed bolt holding coupling to shaft, removed coupling and installed new one. Tightened bolt snugly and pushed agitator bank over coupling! About 5 minutes to repair!!!!!!!!!

First I had no idea what to do. My first thought was to buy a new washing machine and so I began searching and found that a washer equal to mine was over $600. I brewed on this for a few days when a neighbor told me that they are not that hard to work on and we should take it apart and look at it first. We took the top and the front of the washer off and looked at the belt and the motor. All seemed fine. (we just used a screwdriver for that) then we took the agitator off, it pulled right off with some heavy tugging. then we saw the coupling. It was only held on by one screw. We used a socket to take the screw out and pulled the coupling off. It is supposed to fit very tightly on a shaft with gears. When we pulled it off and looked inside it, all the plastic gears in the coupling were stripped and that is why the agitator would not move. I expected this to cost me at least $50, but to my surprise the part was only $6.50. The shipping cost more than the part. When it arrived in about 3 days. I literally had the part on and the washer back together in less than 5 minutes. The entire repair cost me $14 and now the washing machine works better than it has worked in years. Who knew. If you intimidated by working on washers, don't be, they really are very simple machines and so not worth calling a repair man for.

Was very easy to remove and replace. The instructional video let me know what to expect

Unit unplugged. Next day delivery, saved plastic clip and two screws from hose connect to washer , removed leaking hose ,replaced with new hose fully pushed into unit with plastic clip already in place on new hose. Tightened screws on plastic holding clip on new hose. Done complete job in 5 minutes.