YREX4634KQ2 Roper Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
push to start switch didnt work
-
LEE from BUTLER, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
drum not rotating
Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.
Parts Used:
-
Robert G from Dansville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken belt and roller
-
FLOR from Jersey City, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Squeaking noise and stopping during drying cycle
Replaced the Drum Roller, Belt, Belt Tensioner and Rear Drum Seal by watching the video that was attached with the order form from PartSelect. Removed screws from lint filter, raised the top by sliding it forward a small amount, able to raise top and leaned it against a wall. Then removed two screws from front panel and lifted front up slightly while holding the drum and removed it from front of dryer and placed it out of the way. Loosened the tensioner pulley to remove the belt and once that was done pulled the drum out and replaced the drum rollers (by looking at the video). The rear drum seal was the most aggravating part in getting it off and cleaning it up. Was a little messy putting it back on and then just reversed everything to put it back together. It is working properly now. Thanks to the video. PartSelect parts came earlier than I expected they would and I appreciated that very much.
Parts Used:
-
David from Thomasville, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No heat
It took longest to take apart and test to see which part was bad. I had never done it before. Got it apart and used the drawings on Parts Select to find location of parts. Testing only few minutes found bad thermostat.Ordered parts, and they came in 1 1/2 days. I replaced both thermostats being they were in the kit. Actual repair took maybe 15 minutes. Vacuumed out everything I could. Took lint trap out a vacuumed. Put it back together, plugged it in, heated like new. All time told I would say little over hour.
Parts Used:
-
Gordon from Harpursville, NY
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Broken Dryer Belt
Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.
Parts Used:
-
WILLIAM from DELRAY BEACH, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
drum rollers worn out, making kocking noise
just replaced the rollers with the new ones. The trouble was getting the belt around the drum again, but it all worked out and the dryer is running good
Parts Used:
-
Nita from Clarkston, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no heat, dryer would not shut off
I went to partselect.com, input my model number and problem, I clicked on the right solution and watched a short video on how to repair the problem. Ordered the parts which arrived the next day. It took me ten minutes to replace the two parts I had ordered and the problem was solved. I probably saved a couple hundred dollars doing this repair myself..
Parts Used:
-
John from Sterling Heights, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not start
-
steve from hot springs, SD
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not start when I hit the start button
Your website was wonderful--thank you so much! When I saw that 47% of the time this was the problem, I ordered it & it worked! This was a life saver for me! I will come back to this site anytime I have an appliance problem! Thanks again!
Parts Used:
-
Sue from Valencia, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
lint filter was.wornout.
This was replace the old worn out limt filter with a new limt filter effort. Not a difficult repair. I would call it a remove and replace job.
Parts Used:
-
DAVID from ARLINGTON, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat up. Dryer would not shut off when door opened.
I would like to thank the people who created this site. My husband recently passed away from stage 4 esophageal cancer. We only knew he had it for five weeks before he passed. With the medical bills he left behind, I really could not afford to buy a new dryer or hire anyone to fix mine. I do not remember how I found Parts Select but I'm thrilled I did. I first used an ohm meter to find the defective part. Then I followed the step by step video and was able to completely fix my dryer in about an hour. Changing the connectors on the thermal cut-off was a bit of a challenge for me but I managed. I also changed the switch on the door which allows the dryer to shut off when the door is opened. I am truely grateful for this site and will highly recommend it to all my friends and family.
Parts Used:
-
Kathy from Martinsville, IN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
torn lint filter
-
Jon from Manchester, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
my dryer just stoped drying.
I went to parts select website to find out how to repair it myself because when I took the heating coil off I could tell just by looking at it that it was not broke or cracked in anyway so I went to the website to get an idea of how to start diagnosing were the real problem actually was and I found everything I needed from step by step instructions to diagrams and symptom diagnosis and actual pictures of the parts themselfs.
Parts Used:
-
david from calera, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken belt in our dryer
took the top and front off the dryer and had to route the new belt around the drum and through the pulleys, it was really easy and a heck of a lot cheaper then buying a new dryer
Parts Used:
-
tom from mendocino, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!