Models > YMED6400TQ0 > Instructions

YMED6400TQ0 Maytag Dryer - Instructions

All Instructions for the YMED6400TQ0
106 - 120 of 120
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
handle broke off the lint screen
Pulled out old lint screen. Pushed in new lint screen. Time 30 seconds! Why can't all repairs be this easy? ! LOL !!!
Parts Used:
Assembly, Lint Screen
  • Midge Tucker from Greeley, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
latch was broken
Pried edge of latch with dull butter knife. Latch popped out. New one popped back in place. Took 30 seconds.
Parts Used:
Door Catch
  • Danny from Godfrey, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Washer overflowed
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.
Parts Used:
Leveling Foot
  • Beth from Valley Springs, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Parts Used:
Heating Element Connection Wire Kit
  • Betty from Erie, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Broken door catch
Used putty knife to pry broken door catch off .... Snapped in new one. Took maybe two minutes !
Parts Used:
Door Catch
  • James from Ralls, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Door catch was broken
Well the Youtube video was helpful. BUT that only worked on a catch that WASN't broke. I had to bend it up and push it into the door. New one went in easy
Parts Used:
Door Catch
  • LAURA from TWINSBURG, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
broken wheel
I had purchased a motor for the dryer first. The blower wheel broke while I was trying to take the motor off from the blower wheel. Installing the new wheel was fairly easy once I took the blower cover of at the back of the dryer and literally brake the wheel of the motor shaft.
Parts Used:
Dryer Blower wheel
  • Ray from Coleman, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
i had difficult time getting wheel off.
found out that pushing in on wheel and turning counter clock wise, wheel screws off rather easy.
Parts Used:
Dryer Blower wheel
  • dwight from monticello, AR
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Door catch broke in two parts.
I used a screw drivers and put the old one out, and put the new one in. It was very easy for me to do.
Parts Used:
Door Catch
  • Hilda from Wilmington, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken door latch
replacement - pry out the old, snap-in the new
Parts Used:
Door Catch
  • Fred from Missouri City, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
no heat in dryer
diognostic suggested thermal fuse or thermistor. Thermistor tested low resistance (<2K olms). Replaced thermistor and dryer heat returned.
Parts Used:
Thermostat, Internal-Bias
  • Lynn from Huntsville, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer door catch broke
ordered part, recieved in a few days replaced in a few seconds. works perfect.
Parts Used:
Door Catch
  • Lisa from Waxhaw, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer quit before clothes were dry except on the extra low setting. I got an E1 error reading
flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.
Parts Used:
Thermostat, Internal-Bias
  • Betsy from Round Mountain, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Dryer shutting down two to five min. into cycle E- 1
Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.
Parts Used:
Thermostat, Internal-Bias
  • Jack from Gilbertsville, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
Broken door catch
Easy to install - 2 minutes
Parts Used:
Door Catch
  • Bradley from Vienna, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YMED6400TQ0
106 - 120 of 120
Back to Top