YKEMC307KW01 KitchenAid Microwave Oven Combo - Instructions

Fool proof.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

It was a matter of swapping out the old door with new door. In all, it was a snap . Around 10 screws to take it apart and a few brackets to hold it all together.

1. Disconnect AC power 2. Remove back with several sheet metal screws. 3. Remove wires from Limit Thermostat. 4. Check Limit Thermostat continuity -- if open then Limit Thermostat is faulty. 5. Remove Limit Thermostat with two screws. 6. Install new thermostat

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

Removed locking device

I took the new tray out of the box and placed it in the microwave oven.. No tools needed.

I looked up the problem and determined I needed to replace the limit switch which is inside the back panel. As a 78 year old woman who isn't afraid to tackle these problems I found this easier than most. Just be sure to disconnect the electrical connection if you don't have long enough length to pull oven from the wall cabinet. I won't put any sheet pans in the oven next time I self clean it.

Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.

1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1

The oven is a KitchenAid convection oven with 4 panes of glass. The front, two inner glass panes that aren’t “touchable” and the interior glass that is the one that takes the heat from the oven and which you can clean easily - this is important because the descriptions of the glass all say “inner glass”. This is door #3 in the diagram that measure 10 x 22”. Which I cracked when I was pouring water into a pan to create steam for bread baking (lesson learned).

Because of the age of the oven, to remove the oven door it was necessary to place “pins” (we use medium screws) into the hole behind the door latches. Then were able to lift off the oven door. (We saw some videos on YouTube)

We placed the oven door on the counter top and removed ALL screws that held the door at the bottom and around the casing - KEEP these screws separate by where you’ve removed them so you replace them into the proper section when you reassemble the door. Each glass you remove has slots that hold them in their proper places. I recommend taking a picture BEFORE you take out each glass as there are brackets that need to go in proper order and you don’t want to forget the order.

We had to flip the door over in order to CAREFULLY remove the casing and access the different inner glass sections (took the opportunity to really clean them). Gathered the broken glass pieces into a paper bag and vacuumed the fragments. Then we were able to place the new interior glass from PartSelect, and reassemble the oven door. It’s perfect!

This took some time most likely because it’s a very old oven and you need to be methodical. I was just glad to be able to get the part - not yet ready to replace the oven.

BTW, originally I was guided to order glass #7 which is one of the inner glass panes that you cannot touch - unless you take apart the oven door - The exchange for the proper door was handled very quickly and easily. Hope this helps.

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on

shook bottle and painted waited a day and repeated

I put the tray in the microwave???? Pretty easy.