YKCMS1555SW0 KitchenAid Microwave - Instructions

Removed M/W oven case/cover. Identified part needed. Found part online with in 2 minutes, ordered new door latch actuator, installed with part arrived within two minutes, reattached case/cover, reinstalled M/W.

Remove outside cover of microwave.Note that there are 3 unique security screws that you will need a special screwdriver to remove. There is a YouTube video that shows how to install new part. Although this was a lot cheaper than buying a new microwave the cost of $57.00 plus shipping for this 3 inch plastic part was ridiculously expensive.

Remove from cabinetry, take cover off and had a very difficult time removing the plastic form that has the switched in. Replace the lowest of all the switches, and then again very difficult time getting the plastic form back in. Some of the plastic even broke during the process but not any that could prevent it from working as it did before. I had ordered a fuse, 2 packs of 2 switches as there are 3 switches but only had to use 1 to get it working again. Tested after switch install, put the cover back on and reinstalled in the cabinet.

Replaced Door latch Bracket.
Filed a bit off the bracket connection fingers so to fit into the slot.

I ordered the part from partselect (PS972837 Door Latch Bracket) and read all the instructions written here, very easy to do! Saves me a lot of money!

I received my glass cooking tray so fast but when I try to put in the microwave did't fix was to big,I call you today to return and very nice lady help me and told me I need to call whirlpool and explain them and already order again thank so much for all your help you have very nice people in customer service. Thank you so much again. !!

The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.

Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

The only reason it took over 30 minutes was that the unit is a built in over the stove type installation. The special Philips like screw driver which I purchased was the wrong size. I had to use a small vice grip tool to remove and reinstall these screws. The suggestion to use a butter knife to spread the slot was a good one. The delivery from part select was amazing. We were not without our micro more than a few days

Had to remove 3 screws that held the case in place,it removed easily. The control panel that the door latch was locked into required removing two screws and then lifting up slightly while pulling forward. This allowed enough room to put the new door latch bracket into place. Then re-assemble in reverse order. Total time about 30 minutes.

remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced

Followed the instructions that others with a similar problem had written about. Their experience was very helpful. My experience with Part Select was the best! Part recived in less than 24 hours. Happy household, wife thinks I'm worth keeping!

I started by calling a reputable service company to diagnose my problem. The repair tech told me it was the magnetron and it was a "very difficult" repair that required two people because the over-the-range unit needed to be taken down. I asked for a detailed estimate. He quoted $550 including parts and labor. After he left, I researched the part costs on this site and realized his costs were very inflated. I purchased the magnetron for $220. It arrived at my door two days later. Installation was very easy. First, I unplugged the unit. Then, while my wife was making sure it did not fall off the wall bracket, I unscrewed the two mounting screws from the top of the cabinet. I lifted the unit down from the wall and set it on the kitchen counter. The shell needed removed from the microwave which involved about 20 screws. This provided access to the magnetron on top. The magnetron is secured by five screws and a plug. I unplugged it, unscrewed it, and removed the old part. Then, I installed the new magnetron, and tested the microwave to make sure this did the trick. It worked. I put the outer shell back on the microwave and cleaned the microwave. (This is a great opportunity to clean the areas you do not typically see!). I then remounted the unit and plugged it back in. Saved myself a bit of money so I took the family out to dinner and a movie to celebrate. Microwave was in working order for heating up left overs the next day! Thank you!!!

Just took the plate out the packaging & rinsed,dried and put in the oven. I was so happy I found it @partselect online& it came in the next day or two. Will definitely use them again. It was a fraction of the cost from local parts store.

Placed in micro Great sevice. Thanks