YGSC308PJB0 Whirlpool Microwave Oven Combo - Instructions

removed two screws in rear of oven. pulled old element out replaced new one. piece of cake.I am a 70 year old female. if i can do it anyone can.thank you for your swift delivery.

first you have to remove door, so open door all the way, pull back the lever on each hinge, then close door all the way, it will be able to be pulled straight out then, but be careful, its a heavy sucker. I layed a blanket out on table and layed door on blanket, start by taking out screws around the edges of door, keep these in separate container.(don't lose any). now you need to separate the door in half, this can be a lil difficult, mine had grease build up on one end that I had to be scraped . pay special attention to how the brackets go and how the door comes apart, this info will be needed later, now that door is in half, you will need to start taking the 2 other layers of glass out, please pay attention how you take apart, it has to be replaced exactly right. take pics if needed. when you get to the broken glass, take out carefully, and place glass over opening, centered well. now you have to start replacing the other layers, the replaced broken glass is kept in place by pressure, once you get the other glass layers in do not lift up door, you will need to put in the screws under the door, one of which tightens the hinge base to the door, these are the screws that tighten the replaced glass, I found this out the hard way and had to undo the whole thing again to recenter the glass, once tight, just keep going backwards replacing the other half of door. once you do this you will either say, wow that stunk, or wow that was easier than I thought. if you don't have patience, then take the door and glass to a repair shop, because you are dealing with 3 pieces of glass costing 50.00 each. be smart.

Replaced hinges since weak springs were allowing the door to open as the oven heated which would turn on the oven light and give a warning on the control panel. To remove door you need to open the dorr all the way and place a short pin through a hole in the hinge under the hinge point. The pin needs to be short enough that you can get it to pass through the door surround. I cut a short pair of pins from a 16D nail. Place the short pins in the respective hinges and then close the door. Grip the oven door handle and the bottom of the door and lift it free of the oven. Lay the door face down on a towel or blanket. remove three phillips screws from the top of the door and two from the brackets on the bottom of the door. Also can remove the two phillips screws on the door that hold each hinge in place. Seperate the door from the glass and lift out the old hinges. Install the new hinges and reassemble the door. ILift the door back into place. Make sure you install it tight/close to the oven front. Open the door, noting any interference and if it opens freely then open completely and remove the factory installed pins from the hinge and you should be done!

With some help from my wife.

removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.

Turned off circuit breaker. Unscrewed two screws, although they required a square tipped screwdriver insert which I fortunately had phone estimates for this job were between $150 - $180. Could not have been easier.

After a couple hours of frustration, I finally called the repair man and had it fixed properly. All the instructions I got from the the various websites didn't really address my model. Just getting the door off the over (with my type of lock) was a challenge. It is really important to have the proper tools for this job and I didn't have them. Live and learn.

Repair was fast and easy, door closes like new.

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!

Lifted out the chipped one, inserted the new one. Pretty simple.

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

As I did not have a manual, I found all the website instructions very helpful. I had quite a hard time after installing the glass to figure out how to put it back together. The insulation between the oven glass is tricky to keep in tact. I also did not have allen wrenches to keep hinges open, so I used a variety of large bolts and screws. Finally after lots of hours, and almost calling a repairman, I did do it!