YBXR1060T3WW General Electric Washer - Instructions

Pulled off agitator with little effort. One 7/16 bolt to remove and the coupler came right off. Pushed on new coupler, replaced with new provided bolt, pushed agitator back on and was back in business!! Very simple inexpensive repair. Thanks Partsselect for your quick parts turnaround!

My washer was overflowing when filling. Stopped filling when i unplugged from wall so i knew it was the pressure switch because the tube was fine. It took 28 hours from the time i placed the order to the time it hit my front porch. Got home from work and two minutes later i was washing clothes. Thanks for all the info, Tom

I pulled the top of the agitator off (the softener dispenser) then pulled the agitator itself off. I had to pull with some force. I used the socket wrench to remove the bolt on top of the agitator coupling. I then pulled off the old agitator coupling, replaced it with the new part. Used the socket wrench to tighten the new bolt. Lined up the slots on the new coupling with the agitator top, it slid on with a little resistance. The last part to replace was the softener dispencer.

Gently turned washer over onto its front. Removed bottom metal panel (3 or 4 screws on each side). Removed old belt. Installed new belt. NOTE: The new belt is a tight and perfect fit, therefore it will not want fit on to both pulleys/ rotating discs. I have found the best method is to start the belt on the disc that drives the belt. Then place as much of the belt over the disc that sits below the washing machine drum as is possible(the spinning part)and then turn the belt by hand and the belt should pop on to the disc. If the belt goes on easily you may have the wrong belt as the belt must be tight to achieve the traction necessary for the washing machine to spin. HOPE THIS HELPS!! A screwdriver may be handy in helping to pry on the belt. Good look.

replaced the dual water inlet valve

order part. replace

I watched the video you provided and I could't believe how simple it was. I'm 67 yrs old and I just followed the video instructions.

Took the front panel off and it looked like everything was OK with the transmission, etc. Pulled out the agitator and noticed that the coupler had stripped out splines. New coupler was a later design, but was backward compatible with the new bolt included. Spline slipped on with no problem and hold down bolt snugged down just fine. Snapped the agitator back on and was in business.

Installed a new mixing value. Repair went quickly and easily. Repaired machine working great. Easy ordering and the prompt shipping impressed us Greatly!! Thank you!

at 1st, i call GE for service, but i have to wait for the next available field service engineer which is 7 to 8 days to come to my place to check on the washer. the cost is $99.00(non refundable) and then he will order the parts needed for repair another 2 to 3 days. then i decided to buy the parts myself online,and google the web on "how to fix the washer that stopped agitating" everythings in there,with video instruction. pull the agitator up and out by grabbing on to its base. inside, the knot was corroded and the o ring worn out,but really easy to remove with the 11mm socket. the coupling kit although looks different,fit perfectly. insert says its an upgrade of the old model. toss the old and replace with the new, no sweat! now it's shaking like crazy.

An older gentleman neighbor needed help finding a part for his machine. We checked local parts stores to no avail. I researched the internet, found your site and ordered the part. My adult son put the part on in less than 15 minutes. Our neighbor was very happy. We will tell any one in our neighborhood to order parts here. We followed the part watching UPS. The part arrived at the exact day and time. It couldn't be easier.

Removed the four torx-head screws on the top of the washer. Pulled the control panel forward. Removed the four screws on the back of the washer and the two screws that held the dual valve on. These six screws required a nut driver. Pulled the small hose off the old valve. Then reversed the procedure. Total time to replace the faulty old part was about ten minutes. With saftey in mind, disconnect the electrical cord and shut the water valves off at the wall.

Viewed the step by step how to and was able to complete repair all has worked well great info sight!

I replaced the Switch and Valve per the other instructions on this board. It took about 15-20 minutes. After replace, I have not had any overflows since then.

I followed the on-line video with just one exception and I had the old part off in less than 5 minutes. I ordered the part on Saturday afternoon and I had the part in hand by Wednesday morning at around 11:00 am. I spent less time installing the coupling kit than it took to take it apart and had 2 loads of clothes done before going to work on second shift. I would recommend anyone needing help contact Parts Select. They were great and very helpful.