Quick Question!

Have you ever purchased from PartSelect.com before?

Models > XFEF3005LWB

XFEF3005LWB Frigidaire Range - Overview

Get Parts and Repair Help for XFEF3005LWB

If you know the range repair part you need, you can browse the list of all parts on the XFEF3005LWB, or you can search by name or part description. You can also find your part by where it is located on the XFEF3005LWB by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for XFEF3005LWB parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the XFEF3005LWB

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.15

Bake Element - Push On Terminals - 240V

This bake element is used in electric ovens and ranges. It can be found in the bottom of the appliance. It supplies the heat required for the baking function. If your element is no...

$3.13

Drip Bowl - 8"

This chrome drip bowl is designed for use with electric cooktops and ranges. It sits beneath the 8-inch surface burner element. It catches any drips or spills coming from the cookware on your burner. Because the cooktop is a high-traffic area of the kitchen, these bowls often get damaged, or get so dirty they can no longer be adequately cleaned. If that is the case, this is the replacement part you need. The drip bowl is sold individually. At the widest point this part has a diameter of approximately 10 inches. When replacing this part you need to remove the burner element. While you have it out we recommend inspecting the terminals and the element for any corrosion, arcing, or discoloration. Any of those things could be a sign of a bigger problem, and it indicates that the element and terminal block should be replaced.

$2.91

Front Drawer Glide

The front drawer glide is designed to help the bottom drawer on your range slide in and out smoothly. If the drawer is not operating as intended, or the drawer will not close all t...

$3.50

Rear Drawer Glide

If you are having trouble opening your drawer easily or it has been damaged/broken, then replacing the rear drawer glide could be the solution. The glide attaches to the rear of the oven drawer and supports the sides of the drawer. This allows the drawer to slide in and out of range without difficulty. Only one tool is needed for this repair, a flat blade screw driver. Make sure to unplug the oven and wear gloves before repair to protect hands in case range is not cooled before repairing. This an OEM part sourced directly from the manufacturer.

$3.23

Chrome Drip Bowl - 6"

The drip bowl function is to catch grease and spills that come from cooking on your stove top. They are located under the heating elements. Drip bowls are often neglected and can b...

$6.50

Terminal Block Kit

This part connects the wire harness to the surface element and is used for ranges. The kit includes interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing, and wires. If your range/oven is having symptoms such as burner not heating, heating elements not working, burning smell, or if the oven is making a buzzing noise then this could be the solution. The tools needed to replace the kit are wire strippers, a heat gun or hair dryer, and #1 square heard screw driver. Refer to the installation/instructional video for further guidance to accurately replace the element.

$11.36

Surface Element - 8" - 220V

If the burner element on your range will not heat up, or is damaged, it may need to be replaced. This part is 8 inches in diameter, and should not be confused with the smaller 6-in...

$22.64

Infinite Burner Switch - 8" - 240V

The infinite burner switch controls the stove top eight-inch surface burner, which is the large surface element. If your surface element is not warming up, the element can be tested to determine whether or not it is defective. If your element is not defective, then it is more than likely that the infinite burner switch is the issue. Before you install the infinite burner switch you will need to unplug your range from the power supply, or shut off the home circuit breaker. The tools you will need to do this repair include a number one square head screwdriver and a pair of needle nose pliers.

$20.24

Surface Element - 6"

This part is sold individually. This is a part for your stove top. The surface element is what your cookware sits on. The element supplies heat at varying temperatures. This may ne...

$28.18

Infinite Burner Switch - Small Element - 240V

This is a part for your range. This switch controls the stovetop surface burner. If you notice that your stove top is not turning on or is not adjusting to the corresponding desired heat, it is mostly likely due to the burner switch needing to be replaced. You will need a #1 square-head screwdriver and needle-nose pliers. Disconnect the power from the range. You will need to move the range out from the wall to remove the upper back panel to access to this part. This is an OEM genuine part.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven woudn't heat

  • Customer: David from Shawnee, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1099 of 1139 people found this instruction helpful
1. Removed two screws, pulled out the element, voltage tested the element and determined it was an open circuit (bad element).
2. Ordered the part from partselect.com
3. Disconnected element, connected the new one, and screwed it back in. read more

Element cracked in two pieces

  • Customer: Michael from Green Bay, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 713 of 808 people found this instruction helpful
Shut off circuit breaker to stove and collected the tool from the basement. Turned on flashlight. Unscrewed the two hex nuts from the old element/back of the oven. Slid the old element prongs out of the back, exposing the connecting wires. Pulled the connecting wires off of the old element, carefully, so that the connections wouldn't come off of the w... read more

drawer glides were broke on front and back

  • Customer: bryan from sparta, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 531 of 544 people found this instruction helpful
used a screwdriver pushed the old ones out put the new in. the video instructions were great. read more