All Installation Instructions for Frigidaire Range XFEF3005LWA

Replacement bowels didn’t fit

Pulled the heating elements out took the bowels out that didn’t fit, threw them away and replaced them with the perfectly fitting bowels from this site and replaced the heating elements.

Parts Used:

Chrome Drip Bowl - 6"

Drip Bowl - 8"

Russell from ROEBUCK, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

10 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner wouldnt heat

removed element , cut wires, conected wires,replaced element

Parts Used:

Terminal Block Kit

Doug from Ashton, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

wiring was burnt off to burner

The range, (1988 Tappan) was givin to the church by one of our members. While using it, --after a period of time-- the wire burnt off to one of the burners. Since the couple gave us a brand new top for the stove that was still in the box, we decided to fix the stove up.
Now, with new wiring to all four burners, new shiney drip pans and,,,,a new top, we have a very new looking stove for in our church kitchen.
The parts I ordered from PartsSelect, came in just a few days of placing the order,
This is one site that I have wrote down in my address book for any future parts to items we may need.

Parts Used:

Chrome Drip Bowl - 6"

Drip Bowl - 8"

Terminal Block Kit

Margaret from Portage "BlueKnob", PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

12 of 19 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Draw Glide Broken Off Bottom Drawer.

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

Parts Used:

Rear Drawer Glide

Kathleen from fall river, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

9 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Electric burner switch shorted out.

First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

Parts Used:

Infinite Burner Switch

Armando G from Alice, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

9 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replacement burner

Just a replacement burner for my stove. No tools needed. Thank you for such a speedy delivery

Parts Used:

Surface Element - 8 Inch - 220V

Donna from Westfield, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

10 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Enement was blew out.

I order the Element and received just in 4 days. It is Real incredible. I just opened the box and replaced the burners.

Parts Used:

Surface Element - 6 Inch

Chhabildas from Charlotte, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

9 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Large burner wouldn't heat

Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

Parts Used:

Infinite Burner Switch

Phyllis from Elberon, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

15 of 31 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom elerment burnt into

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

Parts Used:

Broil Element

Danny from Gaffney, SC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

8 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven would not heat, broiler still worked.

I unplugged the stove for precautionary reasons.
I then removed the two screws holding element in place with the correct nutdriver.
I then carefully pulled out the element and pulled the two female spade connectors off.
I then compared to new element and plugged the new element in.
Finally I screwed in the new element and tested the oven.
It worked again!! I would recommend running the oven for a bit before placing anything in to bake. this allows burn off of stuff on the new element.

Parts Used:

Oven Bake Element

Eric from Lafayette, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broil element was bad.

It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

Parts Used:

Broil Element

William from Fort Myers, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Socket set

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven light bulb went dark; it needed replacing

Twisted replacement bulb into place easily. Let there be light!

Parts Used:

Light Bulb

Lise from CEDAR GROVE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

9 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

switch not always turn off

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

Parts Used:

Infinite Burner Switch