WU5750Y0 Roper Dishwasher - Instructions

put new seal in and it still leaked!hum

I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on

Came home and my husband had it all done. He said it was simple and it looks bran new again. Very satisfied.

Remove completely the old one and installed the new entire kit.

Opened the door by using a star screwdriver. Pulled the door inside from the outside. Located the broken spring, put in new one (be very carefull to see how the insides are put together..makes life ALOT easier), and carefully put back together.

You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.

The bottom trim piece popped off easily and I removed the damaged panel and replaced it with the new one. I snapped on the trim piece and I was done. It took less than five minutes.

Watched your video and replaced seal in approx. 5 minutes, probably less. Still leaked so I looked at your page for solutions, found out where the air vent was and pried it open, very disgusting mess. With screw driver and long tweezers dug out what I could then poured a mixture of bleach and water in the vent. Totally cleaned it, very white, vent cover went into a bucket of bleach and hot water and it cleaned very well. Put vent cover back on and did a load of dishes, works fine. Thank you for having such a great website, if I ever need help again I will be back. It's a shame someone didn't tell you about cleaning the air vent when you bought the dishwasher.

Put the new part on

Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!

Pulled out old gasket with needle nosed pliers, cleaned groove, installed new gasket just like the video provided on website. Took less than 10 minutes.

Got on the computer, located your site and read the repair stories.Thought, I can do this. Ordered the impeller and seal kit. I followed the same procedures as your other customers, however, when I turned it on for a test it still leaked. Went out looked for a new dishwasher, for $389.00. After talking to my wife,(been married over 60 years)decided to try one more time. Went through the same steps. Loosen the plastic ring remove The revolving spraying arm, tipped on the front to get to the bottom. mopped up the water,disconected water, electric, and hoses. Pulled the motor and pump unit, disassembled the pump unit,then I realized I had installed the rubber and plastic bearing backwards. The rubber to rubber wore out real fast. Ordered a new seal kit (no impeller) Put it all back together and it works just like it did 19 years ago. Total cost less than $60.00. It is a good feeling when your able to fix somthing like this, especially ehen your a fat 83 year old. I would like to meet the person that changed this in a half hour.

pulled out the old seal and put in the new, fixed the leak!

Watched the video and did the repair it was easy.

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.