WU4300Y0 Roper Dishwasher - Instructions

Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

Safety First: 1) I shut power off to dishwasher, 2) Shut water off to dishwasher, 3) Checked electrical with tic tracer to confirm power was off after removing bottom dishwasher panel, 4) I checked the orientation of old valve: connection plate, water inlet tubing, hose connection, and electrical connection. Then I removed the 2-screws that held the valve in place with a nut driver. Next I removed the compression clamp from the rubber hose with pliers and a screw driver. Then I removed the compression fitting and copper tubing from the old valve. Note: Kenmore used a compression fitting to connect the copper tubing to the original water valve. That said, I had to remove the old fitting and install a new one (using a pipe cutter on the copper tubing before installing a new compression fitting). I also bought a new valve elbow because the old one was not serviceable. With all three connections made up (the rubber tubing connected to the new valve along with the electrical connection, and the new elbow and compression fitting installed) I tested for leaks and reconnected the holding bracket to the side of the dishwasher frame. Before calling it good I vacuumed out the area under the dishwasher. Note: because the water inlet valve is located close to the floor, all the work had to be done while laying on the floor...awkward. This too, I had to purchase a new valve elbow and compression fitting so halfway through the project I had to make a run to the hardware store. Overall, replacing the water inlet valve on a 10 year old Kenmore dishwasher is an easy project...pretty straight forward but having to go to the hardware store stretched the installation time out to over an hour.

i took the inside door off and took the 2 switches out and replaced them; not too difficult.

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

I read everyone else's fixes, which were very helpful but my solution of removing the plastic from the motor shaft was a lot easier than others. I simply used side cutters and made two cuts into that plastic piece and it Fell of. much easier than the person using several Dremmel blades to cut it off.. That was the most difficult phase until I grabbed my ole phone company side cuts and just cut it off in 15 seconds. Thanks for all the other tips. I love dealing with Parts Select, Fast and efficient. Jim W

we followed your instructions submitted via e-mail and they worked out just fine....thank you

Started down Parts Select list of possibilities. Replaced the door gasket (1/2 hour), still leaked. Replaced water deflectors (15 min), still leaked. Was looking at steam vent and read the repair submitted by "mary from Fountain Green UT". Removed and thoroughly cleaned the steam vent (1/2 hour). Stopped leaking and is working fine now. Repairs were very easy using Parts Select instructions.

Just removed the old one and installed the new one

Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.

easy to remove the old gasket but did not solve the problem door leaks from the bottom and water remains on bottom of machine

Opened the door removed old seal and put the new one in. The only hard part was getting the new seal out of the package. It took about 1 minute to do. Very easy.

Amazing how quickly the part was shipped and arrived. Very easy to install no tools needed.very pleased with everything . Thank you.

Replaced the heating element that I ordered from Part Select. The repair cost me less than $25.00 and took me less than 5 minutes. I saved $650.00 by not buying that new dishwasher that my wife wanted to replace it with. I'm sure she will find some way to spend the money I saved(lol). Thank you Part Select.