Models > WU3006V2 > Instructions

WU3006V2 Roper Dishwasher - Instructions

All Instructions for the WU3006V2
31 - 45 of 86
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
cut wire in center sprayer to remove plastic holder for new basket
after that every thing went very well
Parts Used:
DISHRACK
  • JOHN from IONIA, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Parts Used:
Power Cord Kit
  • Jonathan from DOWNS, KS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
none
removed and installed cords with screw driver
Parts Used:
Power Cord Kit
  • Ronald from VAN BUREN TWP, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Parts Used:
Power Cord Kit
  • Fred from SICKLERVILLE, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
poor water circulation
follow instructions, unscrew old part, screw in new part, worked like new
Parts Used:
Nozzle Cap
  • Wade from New Carlisle, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
LIght switch on oven door was broken
Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!
Parts Used:
Rocker Switch - Black
  • James from Sequim, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
left door spring broken - door wouldn't stay up
Removed the two screws securing the dishwasher to the underside of countertop.
Pulled the washer out until the spring mechanism was visible. Vacuumed the area - it was filthy. Assembled the spring and adjusting hook. Took me 4 tries to get the spring into the proper tension slot. Having the other side intact helped in understanding how it worked. Used long nosed pliers to bring spring onto the door retaing plate slot after trying unsuccessfully with regular pliers.
Parts Used:
Door Spring Assembly with Adjusting Hook
  • Philip from Hialeah, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher had no water coming into the bottom of it
Took the old one off and replaced it with the new one we received from you. It was great because we received the part just in time to do the Thanksgiving dishes! Thanks PartSelect.
Parts Used:
Detergent Dispenser Cover Kit Water Inlet Valve
  • Kathy from Kennedy, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set, Wrench set
14 of 39 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both Dishwasher door springs broken
Pulled out the DW and removed old spring parts. Used screw driver and pliers to respring
Parts Used:
Door Spring Assembly with Adjusting Hook
  • Claiborne from Atlanta, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door hinge broke
All pieces just snap off and the new one just snap right back in place.

Remeber take a little time to do your repair correctly.

It is cheaper to repair an appliance than it is to replace.
Parts Used:
Detergent Dispenser Cover Kit
  • David from Vancouver, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
7 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
original dishrack had become rusty
installed a new rack
Parts Used:
Lower Dishrack Kit
  • Tom from Peoria, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door spring broke
It took longer to take the 2 screws out than it did to put spring on.
Parts Used:
Door Spring Assembly with Adjusting Hook
  • Kyle from Jonesborough, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lower rack started to rust through coating
Since there were no printed instructions, we looked at the photo schematic.
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!
Parts Used:
Lower Dishrack Kit
  • Carol from St Johnsbury, VT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lid from old basket to be installed on new
Simply bend the lid so hinges slip out of sockets, and repeat to put the lid in the new basket.
Parts Used:
Basket, Silverware
  • Fred from WOODBURY, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Parts Used:
Screw - 8-18 x 1/2
  • Johnny from LEVITTOWN, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WU3006V2
31 - 45 of 86
Back to Top