WTW4750YQ1 Whirlpool Washer - Instructions

1. Removed the fabric softener dispenser

2. Removed Barrier Seal Cover

3. Removed bolt and seal

4. Removed and replaced CAM Agitator Assembly

5. Reversed the removal steps.

My husband just took the bolt in the middle took the broken one, put the new one, put the bolt back the lid the rubber seal and done. Working like new.
Basically we did what everyone else did with this part, it help me realize I did not need to call a repairman for this, I knew hubby would be able to do this.

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .

snapped off the softener dispenser, pulled out the plastic seal below and could see problem. Used socket with extension to remove agitator. ran machine to verify transmission was working.
Looked up parts on line and found Part Select. The repair stories insured me I had correctly identified problem. Ordered part on Sat. arrived Tues. Reversed disassembly process with new agitator. Success
Great source of information, fast delivery, very satisfied overall and will reccomend and use again

I unscrewed the agitator and pulled it out. Then took out the old agitator cam kit and put in the new one.

Removed the fabric softener cup, remove plastic cap that prevents fabric softener from going into the agitator column, removed screw, replaced dog teeth and cap that holds them in place, put agitator back together.... Done.

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.

Went to website and found question to what problem i was having with washer and they gave me a list of parts to fix it. The video that showed me how to change the parts was very helpful. I replaced the Agitator Cam Kit and the thrust washer. It was very easy to do and watching the video before i started helped.

There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.

Removed softener dispenser, removed part under that to reveal bolt that holds agitator on to washer. Figured out there was more to the problem than just the dog ear things and had to end up getting a whole new agitator. Probably saved us $60 minimum in labor and trip charge and was a piece of cake! Took my husband less than 15 mins. to remove old agitator and put on new one. Geez, I guess I have to do laundry again!

I took out the softner dispencer and there is a bolt under tthe the plastic cover,I removed the bolt and the whole assembly came out,then I installed the new one and reinstlled the bolt and plastic cover,and reinserted the liquid softner dispencer.All only took about fifteen min.

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.