Models > WTF330HS0 > Instructions

WTF330HS0 Crosley Washer - Instructions

All installation instructions for WTF330HS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WTF330HS0
46-60 of 245
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washing machine wouldn't drain or spin. It would run through its cycle, but only agitate.

  • Customer: Jen from Lebanon OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 7 people found this instruction helpful
Use a cup to take the water out of the washer. Get at least three large towels -- you're going to have to sop up the water when you disconnect the hoses.

Take the bottom panel off (2 Phillips head screws). Drain pump is on the right side.

Remove the two screws holding the pump to the metal bottom plate. Use a small socket wrench and/or a screwdriver. I had to use a screwdriver on the right screw and a socket wrench on the left screw! Place as many towels in the cavity as you can to catch the water that's going to come out when you detach the hoses.

There is an inlet hose and an outlet hose, attached with bright green clamps. Remove those with pliers. Clean up the water that drains out. The hose in the back (inlet) has a "coin catcher" area. Clean this out.

Attach the hoses to the new pump. Screw it down. Replace the bottom panel.

pump quit working , washer was full of water!

  • Customer: ROBIN from BLOOMINGTON IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 7 people found this instruction helpful
first took off old pump off by removing 2 screws and removed 2drain hoses under front load washer with pair of pliers then put new pump on same as removal.

Front loading washing machine broken shock absorber

  • Customer: Thomas from Epping NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
The illustarated parts break down on the Part select web site was an awesome resource. It identified the exact part that was damaged by part number and comprehensive drawing. The part was ordered utilizing the drawings and on my doorstep within two working days, regular ground shipping. The securing pins were removed from the damaged shock absorber by driving them out with a screw driver (used in place of a drift punch) and a rubber mallet. The new shock absorber was placed in position and the securing pins were installed easily by hand and were securely in place when an auditable click was heard from the securing pin when fully engaged. The shock absorber kit came with an additional securing pin in case one of the original pins were damaged. The replacement part was of superior quality to the original.

Thumping vibration on spin cycle

  • Customer: Kerry from Pasadena CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
Remove the front lower panel. Remove the 4 plastic pins mounting the shocks using 1/2 inch short socket to hold the detent down as per included instructions. All plastic pins were stuck in place so used needle nose pliers to pull or push out. Lube the pins with grease before reinstall to help them go through the new shocks. Use the included lock nuts to lock the four legs in place as low as possible. Start the washer and level each leg while running so you can tell if the vibration is going away. Tedious method but worked.

Rubber seal (boot) needed to be replaced.

  • Customer: Jon from Stevens Point WI
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 9 of 16 people found this instruction helpful
I began by removing the seal from the exterior lip of the machine housing. I took a razor and removed any rubber and adhesive that remained on the unit.

Next, I remove the boot from the soap dispenser tube (located at about 11:00 of the opening) with a needlenose plyers. The manual recommends flattening a 3" copper pipe to fashon a tool to release the "bread tie" fastener. I can see why but patience with a needlenose sufficed.

I pulled the boot down from the tub housing (with much force) exposing the band that holds the boot in firmly. I one pull, both pieces came out. I could tell getting the new one is was going to be a chore.

I cleaned the area and after about 40 strenuous minutes of getting the new boot onto the tub, only a couple things remained. Even with help, be prepared to dedicate hours of frustration getting the band around the boot securing it to the tub. The working space is minimal and the task is virtually hopeless to slightly possible.

Once that's taken care of, you may feel like you can accomplish anything. The rest goes up in the order it came out. Make sure you slide the boot up as far up the soap dispensing unit as possible before securing the bread tie clamp.

Run the seal around, close the door and have one of you kids clean up the work area (and mop the blood, sweat and tears from the unit and the floor.

drain pump stopped working

  • Customer: Robert from Camby IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 5 of 5 people found this instruction helpful
First, I unplugged the unit, then took out the hold down screw. Next I took off both snap rings and layed towels down. Pulled off both hoses. Finally reattached in reverse order. I did not have the problem of others with the snap rings they came off easy and went back on easy.

right side tub mounting spring broke

  • Customer: Lisa from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
disconnected electric and water supply. removed back cover from front loading washer. removed two screws from spring end plate on the top of the washer. replaced old spring with new spring/insulators by lifting the tub and hooking the new spring on. replaced the back cover and top spring cover plate. reconnected water supply and electric. machine is working like it did before the spring broke. very easy fix. the majority of the effort was moving the washer around to get easy access.

Tub to pump hose leaking

  • Customer: Barbara from Los Angeles CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
From the front of the washer, I removed two sheet metal screws at the bottom of the access panel. The panel pulled off with a just a little effort due to the nylon inserts installed on either side of the panel that keep it in place. The tub-to-pump hose is located on the right hand side and easy to access. The hose includes a screw clamp and two tension retainer (?) clamps that need to be removed.Make sure to save them for the new hose! I used a phillips head screwdriver for the screw clamp and a pair of channel locks to remove the tension retainer clamps. The tension retainer clamps were easy to remove but tricky to put back on. There must be another tool used for them that I'm not familiar with. With just a little patience though, it's an easy enough repair for anyone to do.

Leaky Drain Pump

  • Customer: Darrin from Cedar Rapids IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
NO EXPERIENCE NECESSARY!!
Unplug electrical.
Remove lower front panel -2 screws.
Locate drain pump in front right .
Remove electrical wiring plug - press release clip.
Remove mounting to floor - 2 screws.
Remove two hose clamps - pilers.
Mount in new part - 2 screws.
Reattach two hose clamps - pilers
* be sure hoses are fully reattached.
Attached electrical wiring plug.
Attach front panel - 2 screws
Plug in the electrical and be proud of your accomplishment because you just saved a minimum of US$200.00. Congrats.

Kenmore 417.41042000 Front loading washer shakes

  • Customer: Chris from Burtonsville MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no matter what else you fix, this will break and kill it at some point. Piece of crap!

Washer wouldn't spin clothes

  • Customer: Brian from Forest Ranch CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
First thought the problem was with the spin cycle, however it soon became clear it was the pump that wasn't draining the water that kept the spin cycle from doing it's thing. After hand-wringing a large load and shopvacing out the remaining water, I ordered the new pump, got it in two days, and did a quick change out and it works perfectly. During the removal of the rubber boot that connects the tub to the pump, the one thing I did discover was a yucky buildup of years of fabric softener which I couldn't break my wife from using. But, after showing, and more importantly, letting her SMELL the fungus/mildew in the sludge, I've finally broken her of the habit! Best bang for the repair buck so far.

space

  • Customer: Alvin from Woodside NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 6 of 10 people found this instruction helpful
1. replaced (2) shocks, remove bottom cover 2. (1) spring and rib belt, used a wooden block to hold up drum , rolled out ld belt and rolled in new----remove top and rear covers after replaced same ---thanks..

Door latch broken

  • Customer: Steven from Pompton Lakes NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 10 people found this instruction helpful
It was done in five minutes! Piece of cake. I will definetly use your site in the future. We had a servir=ce plan with Sears. They are the worst ever...do not pay the money. You only get India for customer service, and they tell you they are coming, do not show, and when you call them they say there is no service tech in the area. You can not get to anyone who can help it theyu did not show twice! We ended up canceling the service, and to their credit they send us a refund. Funny thing about it, they showed up today and left a message on our door that noone answered...this is after they refunded us.

Door strike broke

  • Customer: Chris from Vernon Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
The store I bought the washer from was going to charge $150 service call and over $60 for the part. I searched on the internet and found what i needed at partselect.com. The part was under $7 and the shipping cost more than the actual part. 2 screws, 1 screwdriver and it was fixed. Thanks!

Basket loose and banging around - both shocks broken

  • Customer: Christopher from Woodbury CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
-Unplug machine and remove all water connections
-Remove back panel with power phillips screwdriver
-Removed some rectangular circuit box in the way of getting to one shock absorber (3 screws)
-Remove old shock absorbers with 1/2 inch socket (suggested in accompanying directions)- this took 2 minutes
-inserted new shocks as directed...this was the most difficult part, but used a hammer to bang into place.
-reinsert and screw down circuit box (or whatever it was)
-reattach back panel
-reestablish water hose connections
-plugged in and was in business
-had ordered a washer/dryer set for $1700 (at my parent's urging) and now can tell Sears to go pound sand!
All Instructions for the WTF330HS0
46-60 of 245