WRT8G3EQ2 Westinghouse Refrigerator - Instructions

Remove 4 screws that hold up overhead controls, this is also the part that holds the light. Unplug the timer and replace. Super simple and runs great now. After you plug it in it may take a few minutes to kick on the compressor but it will. Also I was pleased it was a factory Frigidare part. Price was right.

My husband pulled off the broken piece, then snapped the new one into place. Super easy, quick, and saved us money.

Took less than 1 minute to install. Snap in and DONE. The easiest job ever. Thank You!

When I was moving the refrig. handles from one side to the other...I broke one of the mounts. It was SO easy to order from this place, and they ship IMMEDIATELY. Second time I have used them, and am VERY impressed.

Just unscrewed the two screws holding the handle and replaced the handle and rescrewed the screws. This was the second handle to be replaced but this time it was the original handle part and not a cheap knock off that i first ordered from another company. Thanks Partslect.com for having the original part.

The repair was very easy. I took out the top glass shelf which the drawer is attached to and unscrewed the broken support. Then just lined up the new support and screwed it in place. Placed the top shelf back in the fridge and slid the drawer into place along the new rail supports. Very smooth process.

Remove 1 screw, pull out old part, insert new part, replace screw. Takes longer to clean off the fridge shelf than to replace the part.

Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger

unplug fridge,Then take rack out n remove the 2 screws on the icemaker set aside,then remove 2 screws on the back panel, cut wires n splice in new part! put back the same.

Diagnosis: used wiring diagram attached to frig and determined cause could be wiring, heater element, thermostat or timer. After completely defrosting the frig (turned it off) I removed the rear cover in the freezer and looked for an obvious problem. None seen. Removed temperature select pod from the frig box and looked for obvious problems. None seen but defrost timer appeared poorly made. Repair: Since I had no practical way of checking the defrost cycle in operation, I checked probable failures on the Part Select website and saw defrost timer as most probable. I ordered the timer. Installed it. Waited a few days to make sure the frig went through a few defrost cycles then removed the freezer rear cover. There was no excessive frost buildup so I'm reasonably sure the repair was successful.

In 10 years, this is the second time these drawer supports broke and what a difference to fix. The parts came quickly, fit well and are very easy to install. The fridge is good as new and the cheese/condiment drawer is back where it belongs. Good quality and easy to do.

this was so easy to fix, we don't know how we lived with the broken one for so long. the part fit perfectly, snapped into place without a thought, and now things don't go flying every time we open our refrigerator!

removed broken bar and slipped in new bar

Used wood blocks to raise the door off the lower hinge bracket then unscrewed the suspect hinge. Cut a small shim, two layers of soda can, to place under the lower edge of the new hinge bracket and doubled the washers by using the old one to ensure I had adequate clearance for the door. After a little silicone lube I installed the new hinge bracket. All better now.

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.