WRT771RWYW01 Whirlpool Refrigerator - Instructions

Followed the example on the video and everything fit in place without any problems. Only issue is that on a double door fridge the freezer is rather narrow so there isn't much room to work making it was a bit difficult to access the mounting screws.

Really couldn't be easier. Loosen 3 screws that are easy to find. Disconnect the quick connect wiring harness. Now you have the old unit out. Take out the wire that tells if there is too much ice from the old unit and put it on the new one ( this was the hardest part of the project) Hook up the new wiring connector and hook it on the screws and tighten it up. Viola, your done. No messing with the water. Took me 5 minutes and I've never done it before.

First i pulled the electrical plug from the socket so the refrigator was off than I removed 5 screws (3 of those holding the ice maker). pulled the icemaker toward the front and removed it I than took off the back of the freezer panel,(the back panel was removed by pulling the top of the panal towards me it came right out of the freezer) I removed an additional 2 screws holding the evaporator fan motor. Than I used pliers to squeeze the mounting bracket tabs (white tabs BOTTOM OF MOTOR BRACKET). I then disconnected the electrical FAN MOTOR PLUG and removed the motor. i than pulled the fan blade from the motor (fan blade is only a pressed onto the motor shaft.I than pressed the fan blade back unto the fan motor and reversed the above directions

I watched the installation video and did just like it said. It was pretty easy. My ice maker is working once again, and I'm pretty proud!

Exactly as instructed by video on your site. The replacement took 10 minutes. thankyou Partselect.

Watched the online video and it looked just too simple.....so when I got the new unit I did not have to even change the wiring harness and I was totally surprised that the change could be so simple and easy! Trick is to follow the video instructions and DO NOT take out the two top screws but just loosen them enough to lift up the old unit and remove it! Cannot believe it could be that simple and easy.

Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.

Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.

Viewed the viedo - it showed what to do

watched video, followed the instructions and everything fell into place. since the wiring harness was not removable, I disconnected the harness from the the old unit and hooked it up to the new unit. put every thing back together,plugged in the power cord and turned on the water. water filled the ice maker and ice appeared in about an hour.

ice cubes are now being made properly and there is no more leaking.

Previous to installing the new ice maker - I replaced the dual inlet water valve per the instruction video I found @ partselect website. That did not solve the problem <> I also adjusted the timer on the old ice maker down - per another video / which also did not solve the problem. Then I viewed the video on icemaker replacement - ordered the ice maker & 3 days and 15 minutes later <> the problem was fixed ! This web site is "fantastic" ! Thankyou partselect for your assistance ! ! !

After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.

Removed three screws. Discount wire harness. Reverse proceedure for installation.

Watch the u-tube video first ,Then read instructions that came with new unit ! so darn easy. unplug fridge, remove ice bin, clean and dry bin before putting back in service! stick flashlight in freezer loosen 2 top screws remove 1 bottom screw, unmount unit, unplug wire harness, remove icemaker and put on table, close freezer door !! , Remove sensor arm from old unit in down position and install in new unit. plug in new unit and reattach in freezer. replace ice bin and plug in fridge, that's it!, It took about 2 hours for the icemaker thermostat to say OK lets go had a load of ice in aprox 3 hours from finish. piece of cake. Jon