WRT771RWYB00 Whirlpool Refrigerator - Instructions

Loosened 2 screws,un pluged the wiring harness,pluged the new ice maker in,tightened the 2 screws. . And I now have ice!! Very easy to install. .

Found the replacement icemaker I needed on your web site,ordered and recdeived it within 2 days. Watched the how to video and did the replacement in less than 5 minutes.However,I waited(2 days) for the icemaker to start working, it never did. Thinking there was another problem in the icemaking system, I contacted a local appliance repair shop. They checked the entire system and everything was ok except the new icemaker. Turns out the new icemaker was defective. I contacted PartSelect and reported the technicians findings. I had another new icemaker in 2 days again. I again installed the new one and am now making ice. Thank you for the installation video and the teriffic service.

determend o.k. water flow,determend solenoids o.k.problem had to be ice maker.ordered part on Su. eve.,recieved new part Tue.A.M.,had part installed in 15 minutes. Then waited for quite a long time untill it finally made ice.

Per directions supplied

Removed the old one. The new one had a power chord attached but it did not connect to the wire in the freezer. I saw it could be unplugged from the new ice maker and the power chord from the freezer plugged right in. Once installed, was not sure it worked but after a few hours it filled with water and started making ice. Works great now.

I installed the new icemaker that was missing the shutoff arm then I ordered the arm from you and installed it. End of story.

I have a side by side so the space to work in was limited but I still completed the install in about 30 minutes. Unplugged the refrigerator then loosened the top two screws took out the bottom screw lifted the ice maker out just far enough to disconnect the power cord reversed the procedure. plugged it back in started making ice in 30 minutes. Probably would have not have taken that long my MS slowed me down a little. The repair man was going to be $300.00 plus $$75.00 trip charge what I paid was $128.41 that was with 3 day shipping.

unplug frig, didnt turn off water used cord light to see. Took 1/4 nutdriver and loosen screws removed screw on bottom bracket uplugged ice maker. reversed the process for the new one and done

Followed the instructions, tool out the 'bad' ice maker and replaced it with the replacement ice maker...saved a bunch of money and the job was very easy!!!

I unplugged the refrigerator then I took the bottom screw out of the ice maker. I loosen the other two screws and picked up on the ice maker and it came out. I saw that the top of the ice maker where the screws are they sit in a groove so you dont have to take the top screws out just loosen them and pick up on the ice maker and it will come out. Then I unplugged it from the old ice maker not from the wall of the refrigerator. The reason is I didnt want to mess up the cover that hides the plug in the wall of the refrigerator. Then I took the metal on and off bar off the old ice maker and put it on the new one. Then I took the face off the new ice maker and unplugged the new wire. All you have to do is press down on the little clip and pull back on the plug. Then I plugged the old plug into the new ice maker. Then I set the ice maker in the grooves on the top screws then iput the bottom screw back in then I tighten all screws. I plugged the refrigerator in. I started getting ice in thirty minutes. My wife think I can fix anything now. Thanks

Instead of trouble shooting what part was bad, just replaced the whole unit. Probably cheaper in the long run and the whole process took less than 15 minutes. Pulled the old icemaker out, plugged in the new one and back in business.

Unplug refrigerator.loosen 2 screws,take bottom screw out.Unplug electric connector,take off ice arm,install on new ice maker.Reinstall maker.plug in refrigerator.Really easy to install!

I unplugged the unit Frist. Then I removed the grill covering the compressor and fan from the back. I then located the rear wheel and pin. I bent down the retaining tab and removed the pin and wheel. I installed new wheel and pin and bent retaining tab back to origional location. Replaced grill and checked unit for proper operation.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

fisrt i watched your video loosened two screws removed one removed icemaker installed new one tightened screws had ice in 2 hours i never shut the water off no need