All Installation Instructions for Westinghouse Refrigerator WRT21MR7ASA

Noise from fan

I watch the video on your site and this make iit very easy to do. That repair that tooks me 40 minutes.

Parts Used:

Evaporator Fan Motor Kit - 120V 60Hz

Reginald from WEST PALM BCH, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Plastic runner broken

Got the part. Watched the video. Replaced the Meat Drawer Rail. Just lke that! Easy squeezy! Thank you for making it so simple! ***** (that's five stars!)

Parts Used:

Meat Drawer Rail - Right Side

Pat from LAGO VISTA, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Freezer worked, no fridge

Removed panel over the motor in the freezer department. Removed screws holding the motor in, unplug wires. Reversed process to install motor.

Parts Used:

Evaporator Fan Motor Kit - 120V 60Hz

Adam from BERKSHIRE, NY
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

rail was broken

After removing meat tray the entire shelf including rails needs to come out. Once out a single set screw in the middle of rail needs to be removed. You can then slide the old rail across and then pull it out. Then insert new rail, slide across to lock in place. reinsert set screw. Don't over tighten. Be careful when replacing shelf as left side has air opening for drawer that must to match up.

Parts Used:

Meat Drawer Rail - Right Side

Thomas from ROANOKE, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Fridge quit working.

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

Parts Used:

Run Capacitor

Bill from Bay City, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken draw

Pulled Out Broken Draw then put new one in.

Parts Used:

Ice Container

Willard from Plymouth, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Defrost timer was not working

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Parts Used:

Defrost Timer - 60Hz 120V

Harold from Grants, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

had no shelf bin

Just snapped it on.

Parts Used:

Refrigerator Door Shelf Bin

Kasey from O'Fallon, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Hook on end of snap-on freezer bin broke.

The existing bin fell off when the hook broke as the freezer door was opened. Finding and ordering the replacement part was about as simple as it can be. Delivery time was less than a week. Replacing the bin was just a matter of snapping it in place, which took all of 5 seconds.

Parts Used:

Freezer Door Bin

Benton R. from Elkton, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The hole on the handle mounting block was too low

I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator

Parts Used:

Handle Mounting Block

Sadrudin from SAN DIEGO, CA
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gasket was damaged everything inside would freeze

Pulled the old gasket out and pushed the new one in.

Parts Used:

Fresh Food Door Gasket - Black

Earnest from BOWDON, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

None fit perfectly

Just slid it down into place.

Parts Used:

Freezer Door Bin

Michael from CHICOPEE, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Refrigerator was not cooling properly. At 40-45 degrees milk spoiled

My upper and bottom air diffuser was missing.
Purchased both air diffuser and placed it.

Parts Used:

Bottom Air Diffuser

Marcos from E STROUDSBURG, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Door switch was no longer making my light go on when door opened

I used the youtube you provided. It was pretty straight forward, but I had to make a trip to the hardware store for a bit (hex wrench) to remove the hex bolt head style screws. I was only expecting to need phillips or flathead. I managed to remove one with a set of pliers, and the brought that example to the store for size reference when buying the bit to fit my black and decker drill. The rest was easy.

Parts Used: