WRT15GA2AQ1 Westinghouse Refrigerator - Instructions

There is a local appliance parts store that charges high prices but one can return parts. I ordered 3 things and they got ONE correct. I thought I can do better than this. I went on line and found PART SELECT which provides very good schematics so I could order my own parts with confidence. I got a lll the correct parts, quicker and at a very good price. II have a lot of apartments so this is IMPORTANT to me. PARTSELECT is now my GO To for appliance repairs

Removed old fan motor and installed new one.Not much room for big hands back there.Flexible extensions valuable on this job.

Ordered whole new retainer assembly. New bar was incorrect part, but endcaps were OK, so got old part out of the garbage and straightened damaged areas, used new endcaps, and reinstqalled on door. Works.

took off cardboard removed two screws holding fan housing. Removed new fan and housing from box and mounted new fan to new housing (two screws). Installed new fan and housing. reinstalled cardboard and plunged in power cord. Perfect fit.

We cleaned all the parts we had and did a quick survey of which pieces needed to be replaced. We ordered the parts and they arrived within 48 hours. I snapped the pieces together and put all the shelving back together. I do have one difficult spot where the tab inside the door that the shelving attaches too was also ripped. I filled the spot with super glue and let it set for a day and finished installing the last shelf in a few seconds. The Best News...No more ketchup or juice bottles falling to the floor everytime you open the door!!

my wife did it when I was gone !!!!!!!!!

purchased a defrost theromast,took about 20-30 minutes to take apart & put back together.delivery was in one day from the time of my purchase.thanks for all ur help &prompt delivery.

No tools...just slipped it on.

R&R went fine

Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!

Refrigerator and freezer was not cooling sufficiently due to an inoperative evaporator cooling fan. Replacing the mini evaporator fan was extremely easy. Here are the steps needed to replace the fan. Step 1: Unplug refrigerator/freezer main power cord from the electric wall outlet. Step 2: Remove the food rack from the freezer compartment. Step 3: Using a 1/4" nut driver, remove the (2) 1/4" screws that hold the freezer vent panel/temperature control in place. Step 4: After removing the screws, disconnect the motor's wire harness connector which is located on the top left corner behind the freezer's vent panel/temperature control. Step 5: Pull away the entire vent panel/temperature control panel and lay it flat on a table. Step 6: Remove the vent cover from the main panel by holding the left side and the right side of the vent cover and squeeze both ends at the same time. Step 7: With the motor now being visible pull the motor's fan blade straight off. Step 8: Using the 1/4" nut driver, remove the (2) screws that hold the motor bracket to the rear of the main panel. Step 9: Using the 1/4" nut driver remove the (2) screws that hold the motor to the bracket and the (1) ground wire screw. Step 10: Install new motor back onto the bracket with the original (2) screws and the (1) ground wire screw onto the same locations.Step 11: Re install the (2) screws that mount the fan bracket to the back of the main vent panel.Step 12: Push the motor's original fan blade back on the shaft until it's fully seated. Step 12: Snap back in place the small vent panel back onto the main panel. Step 13: Push in place until you hear a click, the motor's wiring harness connector back onto the top left corner of the freezer's main power wire harness connector. Step 13: Push the main vent panel until it's in place and then reinstall with the original (2) 1/4" screws. Step 14: Reinstall the freezer's food rack back in place. Step 15: Plug in the main power cord into the wall outlet. Get ready to enjoy ice cold drinking water and a super cold freezer. Pete,your weekend mechanic

Replaced broken section

Took out the old tabs that broke off (left inside the retainer bar) with a butter knife - just lifted very gently the ends to slip out the broken off old pieces then replaced with new pieces (pressed lifted sides back down with side of butter knife and then snapped back into door of fridge gently it will pop snap back in - So very very easy to do - should have done this years ago instead of living with taped ends and waiting until husband had time-smiles fridge looks new again do not wait - just do it order the pieces u need and you will be very happy U did

Shipped quick. Assembled by hand. Mounted and tested operational.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .