WRS3R3EWB Crosley Refrigerator - Instructions

two screws fingers pop the hoses off done in 4 minutes

Remove 4 screws to get the housing cover off. Remove the lock ring that holds the ice auger in place. REmove 4 screws to get the crusher housing off. Reverse the order to replace the housing. Very simple.

Your video tutorial was great just did what it said to do. Your service in mailing parts was awesome. Thanks so much!

Had a little trouble getting old pin out of support bracket finally used screwdriver and broke plastic so I could get to the pin and used needle nose pliers to remove hanger then came right out putting new one in was a snap slid in tapped pin in and installed new crisper bracket took about 15to 20 minutes to complete.Contribute difficulty in removing pin to age of refrigerator had been in place for at least 5 years maybe longer overall experience not bad.I am 75 would probably been easier for a younger man more flexible.

I watched the step by step video. I t was a breeze. Thanks for the fast service and number 1 video to show me how to install

Pulled fridge away from wall and unplugged. Turned off main water supply feed and removed fitting from water inlet valve. Took off back panel by removing 3 screws. Took out 2 screws holding valve to fridge. Pulled off color coded wire clips. Unscrewed each water tube connector. New valve had quick connectors so had to snip off flared ends of tubing with utility knife. Pushed tubing firmly into new valve fittings and pulled to ensure connection. Reattached wiring and reattached valve to fridge with the 2 screws. Reconnected water feed line and turned on main water feed. Checked for leaks before replacing back panel. Done. No more dripping from water dispenser.

It went okay. My husband did the job and he is handy. We both watched the little "How to" video and that was very helpful.

Had one other person, so putting the door back was easier. Repair went as told. Could do it myself.

Had to pry the old one from the cabinet. Had to work remaining piece evenly as to not crack the cabinet of the fridge. Not the best design on Frigidaire's part but it was fixable. Thanks for stocking every part under the sun.

I simply pulled out the ice container and auger assembly and,after washing the new one, Iput the new one in and it worked immediately. It couldn't have been any simpler.

Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.

Realized Ice Maker was not getting water during it's cycle and suspected water valve based on other posts to this web site. My fridge is 9 years old and the tubes connecting the valve were plastic screw on type. The new valve did not have threads to accept the nuts. Turns out all I had to do was cut the nuts off and insert the water tubes into the valve which auto-locked the tubes to the valve. Ice maker now works great.

followed guide on enet.

Pulled out the fridge from the wall, unplugged it, and turned off the water supply. Took off the cardboard backing at the bottom of the fridge. Cleaned the dust and gunk. Unscrewed the old valve. Unplugged the 3 electrical connections. Since the new fittings for the water lines were different, we unscrewed the old ones, lopped off the nipples, and inserted the ends of the water lines into the new connections (they were super easy - just push the line in until it clicks). Reattached the valve. Reattached the cardboard. Turned water back on, and plugged in the fridge. Our ice maker still didn't make cubes, though. So I took out the fill valve from the top rear of the fridge. It had a tiny piece of ice lodged in the bend of the back, right above where it connected to the water line. I rinsed it out, reinstalled, and now we have a full bucket of ice!!

problem still persists part did not fix problem. made repairs recommended per your site.