WRS26MZRHD1 Westinghouse Refrigerator - Instructions

Crusher housing had broken so I ordered the part and replaced it. I have since put it back together twice. When I first installed it it crushed the ice no problem. From that point on it seems to lock up and won't crush the ice, cube ice works but the blades seems to hang up after the first use. I can turn the cog by hand but I have to turn it backwards a few times before it turns freely, however it still won't crush the ice. I took it apart and put it back together again. Same thing happened after the first time I tried it. Can you help me. The old crusher broke into. Could something else be locking up?Thanks for the help

Very simple, pulled out the old ice reservoir which contains the feed ice crusher & blade attatched to the shaft. Emptied the old ice tray instaalled thre new tray (after washing & drying) & put it place make sure the motor drive meshed with the new shaft drive. Lowered the ice detector arm & away it went. Probably took 10-15 minutes. I tried to fix the old one twice & spent maybe 3-4 hrs but the repairs never lasted very long.

snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.

I unplugged the refrigerator then removed the temperature adjustment knob from the thermostat which protrudes through the plastic cover located inside the top of the freezer compartment. Then the two hex head retaining screws were removed from the underside of the plastic cover allowing it to drop down and grant access to the bad thermostat control module which was then unplugged and removed from its mounting. The temperature probe is also removed from its sheath at this point as it's attached to the thermostat and has to be removed as well, it simply slides out of the sheath. Installation of the new part is the reverse of the removal of the old part. My refrigerator now works as good as new. Problem solved. The replacement part seemed a little bit pricey for what it is but, in my opinion, was delivered very quickly. As stated by another here, writing this report has taken longer than the repair did.

The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.

Removed old deli drawer. Took front cover off old drawer. Put front cover on new drawer. Put food in new drawer. Put new drawer back in refrigerator.

Easy took front of drawer off and slid on new drawer it fit perfect.

You just slide off the broken part and replace it with a new part. I had to make a slight adjustment to the end of the shelf rail to allow the new piece to properly mate with the old shelf rail.

Very simple. Just removed the old one and slid in the new one. Fit perfectly.

first I replaced the timer control hoping thats the problem,unfortunately situation the same ice build up on the freezer.so I replaced the defrost thermostat.right now I'll still observing the condition if still the same.may be in couple days.so far its good.and to replace the parts is not difficult and easy.

Youtube and then ordered the parts. you save us so much money that we just could not buy a new unit at this time. Thank you so much.

Easily installed the new ice-maker. Rec'd the part in three days.

Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.

pulled down the thermostat cover and unpluged the timer control and replaced it with the new part. total time to repair was about 15 min. there was a vidio on how to replace the new part that just informed me that I did it right!!!!very easy site to find what you are looking for!!!!

I order defrost timer then replaced it but it seemed doesn't work. I order defrost thermostat again then it worked fine until now. Thanks. Part selects.