WRS26MF5ASZ Crosley Refrigerator - Instructions

just hung it on the door. thanks for your speedy delivery. i was great to do business with your company. i will be ordering down the road. thanks again.

1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

Simply placed new bin in place. Took less than 60 seconds.

May need someone to hold a flashlight on area during repair. The bottom ridged-tray does pull out easily, exposing three Phillip-head screws. Remove them. Lift the face plate up slightly and pull out to expose the wiring harness behind it near the top. Push the small clip that holds the white plug together and pull to separate. Set faceplate aside. Find and remove three more Phillip-head screws, one in top middle and two on the sides. Pull the unit forward enough to see the two Phillip screws that hold the metal pieces over the rotating arms of the broken lever. Cannot pull this unit out too far as the water hose from refrigerator restricts movement. Use needle nose pliers to reposition/release the spring clip that rests against the lever. No need to remove the entire spring. Remove the two screws. They are short, so be careful not to drop them or the metal pieces they hold down. Use needle nose pliers to retrieve them if dropped. Lift the broken lever up to disengage its rotating arms from grooves. Remove the broken lever by pulling up or pushing down, depending on where it is broken. Take new lever and insert from the bottom and insert both arms in grooves. Re-insert the two screws and metal pieces (large piece on the left). Place spring clip on arm of new lever. Screw the unit back with three screws. Re-connect the white plug of the faceplate. Reinsert the faceplate on refrigerator by aligning holes with hook-prongs and push in and down to lock in. Add the three screws at bottom to secure. Reinsert the bottom and push in to lock. Check lever operation.

Taking it apart is sort of common sense, however putting it back together can be made a lot easier using todays technology of . Digital photography. Take pictures at each stage of disassembly and reassembly be comes very easy and you may only have to do it once instead of multiple times.

after I contacted Frigidaire and they told me that it was the vent fan and told me where it was, looked up the part and got a new one from Part Select. When it arrived I unplugged the old one and plugged in the new one and reattached the holding bracket. No tools required. I then turned on the dishwasher and it works perfectly. If you get an "ou" error message on your Frigidaire Dishwasher, the money you will save is great!!!!

I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.

Removed the old ice container. Washed and dried the new one and installed. Works wonderful.

Removed shelve from frig. Removed old rails from the shelve and installed the new ones. Reinstalled the shelve into the frig. and installed the drawer. Less than 5min.

I removed the old one and inserted the new. No tools were required. The diagram to order the parts were quite clear and the parts arrived speedily. This company knows how to run a business and keep its customers happy!

Open box, peal plastic off of glass, slide glass onto shelf brackets

First of all--outstanding delivery time. I chose the cheapest 3 to 5 day delivery and the parts arrived the very next day. The closer plate was a breeze. The hinge bearing was challenging becaue it was broken off flush to the bottom of the door so it took some time with a needle nose plyers to break it into small pieces to remove it from inside the door. Once that was done it was easy replacing the hinge bearing, reassembling the door. Like others have mentioned it took the longest time taking everything off the refrigerator door. Just glad PartsSelect suggested ordering both parts at the same time since I had to replace both of them.

The diagram for the shelves is wrong I did not receive the right part. I ordered the crisper glass insert and received the vegetable drawer glass.