WRS26MF5AS5 Westinghouse Refrigerator - Instructions

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

Very easy. I at first misunderstood the instructions. the fridge door remains closed. You pull out the water catch tray "outside" the door. someone said ice tray, thats why i thought i had to open the door to fix it. there are 3 screws that the water catch hides. once removed the control panel comes off which unplugs from bottom easily. then there are screws behind the control panel just removed. after those are unscrewed the rest tilts enough that u can uncrew the little metal bands that hold the arm. replace arm & reverse your efforts & your done. took less then 10 minutes.

The shelf bin is a piece that anybody can clip it on the door in less than 30 seconds. No tools required, just simple common sense.

put 4 screws in door handle everythings else just slides into place. took less than 10 min. frig look new again.

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

The most difficult part was the removal of the existing fan and shroud. There is very little room to work between the condenser and the coils where the fan is located. The old shroud had to be removed as it was not compatible with the mounting for the new fan motor and blade. Make sure to unplug the refrigerator and give the coils some time to cool down. The first step was to remove the old fan blade... it simply pulls off. Next you need to remove the two bolts holding the fan shroud to the floor of the refrigerator. Then you need to remove the old fan motor from the shroud... unplug the wire connection and remove two small bolts that hold it on. I was lucky to have a VERY small ratchet to get into these tight spaces. Now is the really hard part, removing the metal fan shroud takes a lot of twisting and turning to get it out. The coils have a little play in them, but you must be very careful of the tubing and connections. Also, the coils are very sharp. Once this is out, IF you can get it out....I had my doubts along the way, you can start to put the new parts in... beginning with the new fan shroud which fortunately is made of plastic and has some give which makes it easier to get in. Then you can mount the new motor to the shroud with the three new screws. Plug in the wire connection, add the foam tape to the shroud and mount the shroud to the floor of the frig with the original two bolts. Lastly, attach the fan blade. This replacement kit is well constructed, fits perfectly and contained all the necessary parts (fan motor with wiring connection, mounting screws, wire connection adapter, fan shroud, foam tape and fan blade), but no detailed instructions come with it. I was lucky to get the old fan shroud out without doing any damage to the surrounding parts, but this part was very difficult for a do it yourself person. I would be interested to know if a professional has some other tips for this part of the replacement process.

Super easy. That was super cool and saved me $500.00.

A plastic guide rail broke after the meat keeper drawer was left open and the refrigerator door was shut on the drawer, this has happened a few times over the last 6 years. We chose to change out both rails at the same time. We removed the meatkeeper drawer, then the shelf above as the rails are attached to the shelf. We removed the rails (one screw on each side. When the new rails came in, we replaced them with the screws. Super easy!

First I removed the door. Took off the broken parts and replaced them. Easy and fast to repair.

One of the bins on my freezer door had the tabs, that hold it on the door, broken off. I orginally ordered the wrong item, but I called right away and Parts Select had the correct item to me immediately. It was a very easy fix, I just had to snap the bin in place once it arrived.I am very impressed with PartSelect and their service. I would definately use them again and recommend them to others.

Remover 3 screws from bottom of panel,unplugged elrc. connector,removed 2 "small" screws from the pivot axel of the broken actuator.Cleaned everything. Reversed the process to reinstall.

Removed stuff on door, removed 2 screws on top of door, lifted door off replaced one door closure/hinge bearing and one door closing plate and put door back on and wala no more thump.

Silly me. It couldn't possibly be the filter because it's worked for the last 9 months with no problems. Decided to replace the water filter base first. Repair was easy. I saw someone had trouble removing tubes from old base and I gave it a couple of tries to no avail so decided to cut the lines instead. Made it even easier. After repair, water continued to leak. So, replaced the filter itself and voila - leak fixed. Make sure you check the filter first. My mistake turned a $40 - 10 second repair into a $100 - 20 minute repair. Good Luck!

door handle off but 2 screws top and bottom of handle that attach to door remained under top and bottom molding. had to remove molding which was tricky. Held onto door with plastic clips which several broke when trying to get molding off. Figured out I had to tap top molding up to remove. unscrewed pieces of door handle and attached new handle. Had to use contact cement to secure molding to door where clips had broken.

First I removed two screws per rail and removed the old rails. I replaced with the new rails and used a nutdriver to secure in place. This was extremely easy and I fell like my fridge is brand new again.
You can do it!!!