WRS23W0AWD Westinghouse Refrigerator - Instructions

I needed one with the adapter. I installed it and there was ice in the tray the next morning...no problem

Drove pins all the way thru supports & then pryed support off. Tapped new supports in place. Watch the vidio on installing new supports. I probably wouldn't have been able to get the supports off without the trick I learned to just knock them on thru. Took all of 5 minutes to replace 4 supports.

Replacement took about 10 seconds, just put it onto the holding brackets, pressed down and presto...DONE!

I followed the website instructions, step by step. The web instructions were great. Easy to understand. Complete. Do yourself a favor.... just follow the instructions off the web! Great service! I am so happy to have found Part Select and will recommend to my friends.

Ordered the part from PartSelect. Estimated time for slow delivery seven days. I got it in three. Removed the cover from the water and ice maker dispenser arena held on by three screes. I had to use an easy out on one rusted scree. Disconnected the wiring to the switches and lat the Circuit Board come forward by removing three small screws. Using tweezers to catch the screws, I removed two small screws holding the broken actuator and put the new one in its place making sure the spring was properly located and the ice maker swivel was under the hold-down strip along with the new actuator. I reassembled the door cover and got a drink of cold water. By the way, always unplug the refrigerator because that area is hot. Dr Robert E McGinnis author of In Search Of Paradise and many other fine books found on Amazon.

Simply removed two screws from top hinge and lifted door off bottom hinge. Next leaned door over and removed broken portion of bearing. Finally reinstalled door and works like a charm. Thanks too this site painless repair. Oh ya part is a perfect fit.


Thanks Clay


P.S. Would recommend to a friend. Note shipping WOW. Please consider using US Mail. Shipping more than part. OUCH.

remove everything from door, remove plate and screws from top of refrigerator, disconnect water feed for ice maker underneath, remove door, be sure to remove any remnants of old parts, replace with new (i had to make a hole in the bearing for water feed, I may have ordered the wrong part, but it still worked, fridge side would not have water feed to worry about), put door back on, re-connect water, replace screws on top.........done.

Removed the top hinge pin and lifted the door off the bottom pin. Removed and replaced the bottom defective parts and reinstalled the door. Reinstalled the top hinge pin which completed the project.

1-Remove upper plate with phillips screw driver (6) screws 2- remove upper hinge plate with ratchet and socket (2) bolts 3- lift door off bottom cam, lay door flat on floor. 4- Remove broken cam on lower part of door, just pull out. 5- Install new cam in bottom of door 6- raise door up, set on cam, reinstall top bolts and screws 7- p. S. Make sure you trace top hinge location with a pencil before removal, so installation has proper location.

Unscrewed top part of door,put it down and replaced hinge bearing,apply some grease,put door back and done very easy do it yourself.

I removed the top door hinge, and then lifted the door off the bottom hinge. The bushing which helps close the door was completely worn away. I pulled out the left-over bushing parts, installed the new bushing I had ordered fro you, and reinstalled the door. It works perfectly now.

I read other comments and most suggested the fix is less than five minutes and a couple tricks (push the remaining piece into the frig if you can't pull out with pliers)and I did exactly that. Parts came in 2 days, repair took 5 minutes - it took longer to open the package. My wife thinks I'm a star!

This repair was the easiest I have ever done. Took longer to clean the door before putting it all back that to replace parts.

with helper to remove door and lay flat to remove bearing with needle nose pliers. Popped out old and installed New one by pushing in. Reinstalled door and tightened small screws making sure door aligned properly. Replaced Door Bin.

Have not really done the repair yet( frig is still to full of Thanksgiving leftovers) but I am sure that with the video that was provided by this site the job will be very simple. Many thanks to the person who put the video together.
John Donnelly