Models > WRS23MW3AWL > Instructions

WRS23MW3AWL Crosley Refrigerator - Instructions

All Instructions for the WRS23MW3AWL
391 - 405 of 524
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken door handle
Even though we did not have the model or part number I was able to easily locate the exact part because of your photo, dimensions and video instructions.
Parts Used:
Door Handle
  • Larry from Salem, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broke fan blade while trying to remove dust.
Removed old fan motor and installed new one.Not much room for big hands back there.Flexible extensions valuable on this job.
Parts Used:
Refrigerator Condenser Fan Motor Kit
  • Jack from Kiefer, OK
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
Water Dispenser Actuator Broken
Removed tray by pulling out. Took out three screws at bottom. Lifted up on face plate. Remove three screws at top,pulled out to access actuator,relieved spring. Then took out screw on the right,loosened two screws on the left and removed broken part. Put in new part and reassembled.
Parts Used:
Water Dispenser Actuator
  • marvin from columbia, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drawer support broke.
I was worried that the support was a permanent fixture in the refrigerator wall. But I pried it out and replaced it with the new part. Holes were exactly the same size so the new part easily replaced the old one.
Parts Used:
Crisper Support - Rear
  • nancy from Bellingham, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Fan would stop or turn slowly. outside of refridg hot
took off cardboard removed two screws holding fan housing. Removed new fan and housing from box and mounted new fan to new housing (two screws). Installed new fan and housing. reinstalled cardboard and plunged in power cord. Perfect fit.
Parts Used:
Refrigerator Condenser Fan Motor Kit
  • Rusty from Howell, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
support clips broken for 2 bins
Purchase was easy. Delivery was quick. Install videos was accurate. Made it eady to as DI project. Safe place for purchase and support. Saved on cost of professional visit.
Parts Used:
Crisper Support - Rear
  • Thurlowe from Tampa, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Refrigerator door would not close properly
We watched your video online and just followed the instructions. It was super easy to follow and install the new parts. We would highly recommend your site to anyone. The parts came in the mail in 3 days. Thank you very much for saving us to call a repair person and saving us about $100.
Parts Used:
Door Closing Cam Hinge Bearing
  • Jeff from Rapid City, SD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Compressor running constantly with freezer temperature at -20 degrees fahrenheit.
Since the evaporator was all iced up, I decided to replace the least costliest item (defrost thermostat kit); did not resolve the problem. Once I replaced the freezer temperature control thermostat, the freezer temperature stabilized right at 0 degrees fahrenheit with dial on factory setting. Compressor no longer running constantly.
Parts Used:
Temperature Control Thermostat Defrost Thermostat Kit
  • Steven from Raymond, NH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Plastic bearing broke on refrig door
The part number was easy to find on the diagram. Delivery was as promised. Instructional film was very helpful and reassuring. Only problem was that the broken part left in the door was difficult to remove as it was distorted and would not slide out. Took considerable persuasion by screwdriver and pliers to remove remaining portion. New part went right in and reassembly was easy. Door works fine now.
Parts Used:
Hinge Bearing
  • William from Ashland, KY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
crisper shelf support broken
Remove crisper and shelf. Use a small punch and hammer to gently push the tightening pin through to the wall of refrigerator, keep in mind you'll need to remove this piece with small needle nose pliers before installing new part. Set new part in place and lightly tap the pin in until flush. Install crisper and enjoy the rest of your day.
Parts Used:
Crisper Support - Rear
  • James R from East Stroudsburg, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken cover support
Remove cover, puch old pin into hole. Remove old support. Set new support in & drive pin in flush. Replace cover.
Parts Used:
Crisper Cover Support - Front
  • John from Frederick, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken Door Closing Cam
Instructions made the job very easy. Parts were an exact replacement. Thank you
Parts Used:
Door Closing Cam Hinge Bearing
  • Allan from Moon Township, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
light socket overheated and crumbled
remove and replace socket. adjust light switch so that it turns light off when door closes.
Parts Used:
Light Socket Light Switch
  • Wayne from Summerville, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Water Tube That Fills Ice Maker Leaking Water
Undone the water line that comes up the back of the refrigerator and pulled the water tube out the back of the refrigerator and reinstalled the new one and reinstalled the water line. Done
Parts Used:
Water Tube
  • PAT from BATON ROUGE, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Crisper cover and front support clips were broken
Removed broken cover frame and drawer.: saved unbroken glass .With putty knife removed two front broken support clips.Inserted new support clips installed new ,cover frame installed drawer replaced glass cover and turned refer over to wife.
Parts Used:
Crisper Support - Rear
  • Lafayette from Winnsboro, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WRS23MW3AWL
391 - 405 of 524
Back to Top