Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer screeching during spin cycle.
Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.
I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken drive brlt
I happen to be a mechanic so the repair was quick and saved me from buying a new washer! But the step by step videos yhat come with your parts are very easy to understand . This company has saved me thousands of dollars on new units or calling a repair company
Watched the repair video on PartSelect website , repair was exactly as they showed on video , grab old agitator at base , give a quick pull and it popped right off , lined up tabs to coupler with new agitator and gave a sharp push down and new agitator snapped right on. Total repair time was approx 5 minutes .
This was a easy job for the do it your selfer. I had no problem the part ,it was like the same one I took off. Now I know where to come for parts . It was perfect . Thanks again
First I unpluged the unit then I remove the hot and cold water hoses from the back. I removed the torx head screws that hold the control cover at the top of the washer, then I located the water valve. Once I located the water valve I took the 2 phillips head screws that hold it in place out , unpluged the electrical connecters took the water supply hose off. I then removed the old valve and replaced it with a new one.Then I put everything back together. very simple job 10 minutes tops.
Unpacked the agitator from the box. Manually pulled off the old agitator and snapped on the new one. Total repair time was under 2 mins. Much better than a $120 service call.
Use flat head screw driver to push in clips that hold on front panel. use plyers to remove hose clamps on motor and remove hoses. use nut driver and remove two screws holding bracket in place. disconnect two wire plugs. Install motor and work above in reverse. very simple 15min job at most.
1- Shut off water and unplug unit 2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute) 3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes) 4- disconnect old pump it will look slightly different then the one you bought! (3 minutes) 5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes) 6- fill it with some water/ spin it out
15 minutes - 30 minutes tops! Good luck Matt East Islip NY
Washer wasnt draining properly, yet you could hear the pump turning.
Blowing hard into the drain hose would force the water off the impeller and allow the pump to reach proper speed to correctly drain. Start by unplugging the machine. To replace the pump, I simply removed the front cover of the washer. There are 2 clips to release along the top of the cover, then carefully pry forward and then lift it off the bottom clips. There are two wires which were a bit stubborn to remove. Carefully wiggle and pull with pliers, and be sure to note which one goes where. There were 2 bolts to attach the pump to the machine, which I removed using a 1/4" drive socket set, the size of the bolt head escapes me - on the small side anyhow. Also two squeeze clamps holding 2 hoses, which were easily removed using pliers. Pull the hoses and watch a pint to a quart of water dump out on the floor. Reverse the process to install. The hoses are tucked back in there, so you may want a flashlight to make sure you get the clamps back on correctly. Replace the front cover, and dont forget to plug the machine back in and you are ready to rock.
Popped the front cover off and found a small hole was in the drain hose going to the pump,used pliers for one clamp and nut driver for the other clamp,removed bad hose and installed the new hose,ran water pump after putting some water in the tub,checked for leaks,put the front cover back on,that was it.
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy
First I found out on the web how to open the washer's front cover. For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible. For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.