WPRE6100G0WT General Electric Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cold water was dripper after each washing cycle.
1)Remove the 5 screws from the back panel to gain access to the dual inlet valve. 2)Disconnect the wire from the valve. Then, remove the screws the hold the valve. Then, remove the C-clamp from the valve to get it loose. 3) Then, reverse the procedures to install the new valve.
Parts Used:
-
Roque from Brentwood, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
hot water only
Unplug washer, turn off water and remove the supply hose, remove 5 torex screws remove panel disconnect two wire plugs remove 2 philips screws squeeze hose clamp remove old valve install new valve reversing directions
Parts Used:
-
John from Milford, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Cold Water Inlet Value Dripping/Leaking
Unplugged power cord and shut off water supply. Then removed both water hoses from the dual water inlet value using adjustable pliers. Next removed four (4) star screws on top of the control panel. This required the purchase of a #20 torq screwdriver from sears costing $3. 99 Plus tax etc. Once the top panel lifted upward and to the left I was able to unplug both electricle connections on the water inlet vlaue. Next unscrewed two phillips head screws holding the water inlet value in place. Installed the new water inlet value in reverse of above. Time to complete was 22 minutes. Very easy repair to accomplish.
Parts Used:
-
WILLIAM from HAMPTON, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Friend thought the belt was slipping.
Changing the belt didn't solve anything. We took the console apart and there is a Troubleshooting Guide folded up in there. It has a Code List and a sequence to follow to determine the trouble codes. While there was nothing wrong as far as coding, it did lead us to confirm the discharge pump WAS working, even though there was no water coming out. The discharge hose was plugged.
Parts Used:
-
Timothy from Galesburg, ND
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
One of the paddles broke from washing something that wedge in between one of the paddles and side of tub. Which broke the blade. Order the the part from Parts Select. Watched the Video how to change the Agitator. It was as easy as they said. Repaired it myself for least than $50.00.
Pull the Agitator out by hand no tools where needed. Took Fabric Softer dispenser off put it on new Agitator. Pushed the new Agitator on. Repair done. Sure am happy I did it myself. Service charge from repair company would have been a lot more then $50.00.
Parts Used:
-
Pamela from Locust Grove, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Water tem,perature was either all hot or all cold.
Replaced the sensing thermistor. It was necessary to remove the front and top panels to get to the location at the water inlet. The wiring diagram located in a pocket in the control panel actually had good instructions for the disassembly.
Parts Used:
-
J.W. from FORT DAVIS, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Would Not Spin Would Not Drain
Easy I followed the video. It took approx. 15 Min. Thanks to the video I feel like I can repair anything. This is not the first appliance I fixed. Thanks to parts select.
Parts Used:
-
William from Urbana, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!